15
120v
LITHIUM-ION
TM/MC
Start lever towards the handle and hold it in
position. The motor will start to work, blade
will rotate. Then release the safety lock
button. (See Fig. 20
)
3. During the normal operation, once the
capacity of battery pack becomes low, the
LED light of Power ON/OFF button will turn
red.
Battery Packs Transfer.
If there are two battery packs installed, one
of the battery packs will automatically be
powered OFF. The mower will work until
the red LED light flashes and the tool stops
working automatically. In this case, release
the blade Stop/Start lever, the power supply
will be automatically switched over to the
other battery pack. The LED light for power
ON/OFF button will turn green again. Then
operate the mower as per step 2.
CAUTION!
1. Do not start the motor in tall grass.
2. Before starting the lawn mower, ensure
that the battery pack and safety key are
correctly installed in place.
3. Before operating the lawn mower, remove
stones, loose pieces of wood and other
objects from the cutting area.
To Switch OFF:
1. Release the blade-Stop/Start lever.
2. Depress the center point of power ON/OFF
button, and hold it in place for 2 seconds. The
LED light will turn RED. Release the power
button. The red LED light will flash three
times then turn off.
3. When mower is powered ON but there is
no operation for 3 minutes, the LED light of
power button will flash for 3 seconds then the
mower will be powered off automatically.
WARNING:
The blade will continue to rotate for 3 seconds
after the mower has been switched off.
Use the Self-propelled function
This unit is equipped with self-propelled system.
The self-propelled function can be used
independently and together with the cutting
blade operating, it is not dependent on the blade
rotation.
Use self-propelled function without blade
rotation
1. Turn the power ON/OFF button ON.
2. Push the self-propelled switch lever towards
the handle and hold it in position. The lawn
mower will start to move automatically.
(
See
Fig. 21
)
To adjust the speed, please refer to “Adjusting
the self-propelled speed” section. (See Fig.
14
)
3. To stop the moving lawn mower, just release
the self-propelled switch lever.
Use self-propelled function with the blade for
cutting
1. Start the mower as previously mentioned.
2. While holding the blade-Stop/Start lever
with one hand, then also engage the self-
propelled switch lever and the machine will
then start to move automatically.
3. Adjust the self-propelled speed-adjustment
lever to the desired driving speed.
Operate the lawn mower
Operation on a slope:
Slopes are a major factor related to slip-and-fall
accidents, which can result in severe injury.
WARNING:
Always be sure of your footing
on slopes. Operation on slopes requires extra
caution. If you feel uneasy on a slope, do not
mow it.
DO:
- Mow across the face of slopes; never mow
up and down. Exercise extreme caution when
changing direction on slopes.
- Watch for holes, ruts, rocks, hidden objects,
or bumps which can cause you to slip or trip.
Tall grass can hide obstacles.
DO NOT:
- Do not mow near drop-offs, ditches or
embankments; you could lose your footing or
balance.
- Do not mow slopes greater than 15 degrees.
- Do not mow on wet grass. Unstable footing
could cause slipping.
Mower overload protection
To prevent overload conditions, do not try to cut
too much grass at one time. Slow down your
cutting pace or raise the cut height. Your mower
has built-in overload circuit protection. When the
mower is overloaded, the motor will stop. switch
Содержание PRO Y0LMX22S300
Страница 4: ...4 TM MC Fig 5 Fig 7 Fig 9 Fig 11 Fig 6 Fig 8 Fig 10 Fig 12...
Страница 5: ...5 120v LITHIUM ION TM MC Fig 14 Fig 16 Fig 18 Fig 20 Fig 15 Fig 19 Fig 17 Fig 13...
Страница 23: ...23 120v LITHIUM ION TM MC Fig 5 Fig 7 Fig 9 Fig 11 Fig 6 Fig 8 Fig 10 Fig 12...
Страница 24: ...24 TM MC Fig 14 Fig 16 Fig 18 Fig 20 Fig 15 Fig 19 Fig 17 Fig 13...
