background image

850 REV04 REV DATE: 09/03/2014                                                                                                                                                         

Page 

4

 of 

16

 

 

 

3.0 Before Installation

 

! PLEASE NOTE

 

When establishing the mounting position for 
the Prism mounting Hardware, please insure 

 

the stability of the wheelchair is not 
compromised.

 

 

Adjusting the forward and aft position of the 
backrest will alter the user‘s center of gravity within 
the wheelchair. A recessed back position can 
significantly reduce the rearward stability of the 
wheelchair. Similarly, a more forward back position 
will reduce the wheelchair’s forward stability.

 

 

The Back Mounting Plates and the Cane Clamps are shipped pre-assembled

 

with the hardware oriented in the forward most back position (see Fig. 1 
below). By altering the orientation of the Cane Clamps with the Back 
mounting Plates, the hardware can be positioned to provide a rear most 
mounting position for the back if desired (see Fig. 2 below).

 

To make the adjustment from the forward most to the rearmost position 
(or vice versa), detach the Back Mounting Plates from each Cane Clamp by 
removing the 3 Depth/Recline Adjustment Screws. Then turn the Cane 
Clamp 180° and re-attach it to the Mounting Plate in its original orientation.

 

The  Prism  Hardware  offers  users  a  full  5”  range  of  forward  and  rear 
adjustability (Angle adjustment forward 15°, back 20°).

 

Each mounting plate provides an individual adjustment range of 1.5”.

 

 

Front of

 

Fig. 1

 

Front of

 

Fig. 2

 

Wheelchair 

Wheelchair

 

 

 

 

 

 

 

 

 

 

 

 

 

 

                 

 

Back Mounting Plate in the                                   Back Mounting Plate in the

 

Forward most back position 

     rear most back position

 

 

Содержание Prism BASIC

















Отзывы: