FUTABA T32MZ, Инструкция по эксплуатации

Страница: 49 / 189

49
＜
Model Basic Setting Procedure
＞
ŏ6ZDVKSODWHFRUUHFWLRQ([FHSW+PRGH
Operation of the swash plate near the hovering
SRLQWFDQEHFRUUHFWHGE\VZDVK$)5IXQFWLRQ
FRUUHFWLRQPL[LQJ8VHWKLVZKHQSLWFKDLOHURQ
and elevator operation causes the swash plate to
deviate from the normal direction.
&DOOWKH6ZDVKĺ6ZDVKGHWDLOVVFUHHQ
Pitch slow side and high side linkage correction is
DOVRSRVVLEOH$GMXVWVRWKDWSLWFKRSHUDWLRQFDXVHV
the swash plate to move up and down in the
horizontal state.
5. Throttle curve setting
This function adjusts the pitch operation curve in relation to
the movement of the throttle stick for each condition.
(17 points curve)
The pitch curve can be freely selected from linear operation
curve to smooth curve, and adjusted to match the curve you
want by means of the T32MZ’s powerful Curve Edit Function
(Six types of curves can be selected). Up to 17 points can be set
for linear or curve types. However, when using the 3 points or 5
SRLQWVVSHFL¿HGWRFUHDWHDFXUYHDVLPSOHDQGVPRRWKFXUYHFDQ
be created by selecting the curve type and reducing the number
RILQSXWSRLQWVWRRUDQGWKHQHQWHULQJWKHVSHFL¿HGYDOXHDW
the corresponding points that you created.
6HWWLQJH[DPSOH!
Call the throttle curve of each condition with the condition
select switch.
ŏ1RUPDOFXUYHDGMXVWPHQW
Normal curve uses Normal (Linear) type and creates
a basic pitch curve centered near hovering. This
FXUYHLVDGMXVWHGWRJHWKHUZLWKWKH7KURWWOH&XUYH
(Normal) so that the engine speed is constant and
XSGRZQFRQWUROLVHDVLHVW
ŏ,GOHXSFXUYHDGMXVWPHQW
The high side pitch curve sets the maximum pitch
regardless of the engine load. The low side pitch
curve creates a curve matched for aerobatics
(loop, roll, 3D, etc.).
Note: :KHQWKHFXUYHW\SHLVFKDQJHGWKHGDWDLV
reset.
ŏ7KURWWOHKROGFXUYHDGMXVWPHQW
The throttle hold curve is used when performing
auto rotation dives.
4. Helicopter linkage
Connect the throttle rudder, ailerons, elevators, pitch, and
other rudder linkages in accordance with the kit instruction
manual. For a description of the connection method, see
"Receiver and servos connection".
*The channel assignment of the T32MZ is different from
that of our existing systems. (The channel assigned to each
function can be checked at the function menu of the Linkage
Menu.)
ŏ:KHQWKHGLUHFWLRQRIWKHOLQNDJHLVUHYHUVHGXVH
WKH5HYHUVHIXQFWLRQRIWKH/LQNDJH0HQX$OVRXVH
WKHVZDVK$)5IXQFWLRQLQDQ\VZDVKVHWXSRWKHU
PRGH
ŏ$GMXVWWKHGLUHFWLRQRIRSHUDWLRQRIWKHJ\UR*\UR
side function)
ŏ&RQQHFWWKHWKURWWOHOLQNDJHVRLWLVIXOO\FORVHGZLWK
the trim setting all the way down.
ŏ $GMXVW WKH QHXWUDO SRVLWLRQ DQG UXGGHU DQJOH DW
WKHOLQNDJHVLGHDQGILQHWXQHZLWKWKH6XE7ULP
function and End Point function (rudder angle
DGMXVWPHQW7RSURWHFWWKHOLQNDJHDOLPLWSRVLWLRQ
can also be set with the End Point function.
+(/,
&237(5