Fulham HOTSPOT LED FHSAC1-UNV-40L Скачать руководство пользователя страница 3

Page 3 of 7

2017-735-3 Rev A

SPECIFICATIONS

MECHANICAL DATA

100%-1%,0%

 

E477042

LiFePO4

FHSAC1-UNV-40L

Fulham extends a limited warranty to the original purchaser or first user for a period of 5 years from the date of manufacture when properly installed 
and operated under normal conditions of use. For complete terms and conditions, please refer to the Warranty Center at www.fulham.com. 
Specifications subject to change without notice.

Figure 7

Figure 8

Figure 9

Figure 10

Figure 11

Figure 12

88

90

(%

)

Efficienc Vs Output Voltage at 277Vac

750mA

80

82

84

86

Efficienc

1000mA

1250mA

1400mA

20

25

30

35

40

45

50

55

Output Voltage (V)

80

100

120

140

e

(Khrs)

Lifetime vs Tcase

0

20

40

60

50

55

60

65

70

75

80

85

Lifetim

e

Tcase(

°

C)

6

8

10

(%

)

THD Vs Output Power

277V/60Hz

230V/50Hz

0

2

4

20

25

30

35

40

THD(

Output Power (W)

120V/60Hz

p

(

)

80

90

100

110

Io vs Ext.NTC Curve

10

20

30

40

50

60

70

80

Io

Ratio

(%

)

0

0

2

4

6

8

10

12

14

16

18

20

Resistor of Ext.NTC on Module (Kohm)

60

70

80

90

100

110

tio

(%

)

Io vs Tcase(driver)

0

10

20

30

40

50

50

60

70

80

90

100

Io

Rat

Tcase(

°

C)

0.95

1.00

r

Power Factor Vs Output Power

277V/60Hz

0.75

0.80

0.85

0.90

Po

w

e

r

Facto

r

230V/50Hz

120V/60Hz

20

25

30

35

40

Output Power (W)

Содержание HOTSPOT LED FHSAC1-UNV-40L








Отзывы: