Fujitsu SPARC Enterprise M3000 Скачать руководство пользователя страница 167

Страница: 167 / 560

restoredefaults(8)

System Administration

143

EXAMPLE 2

Restores the server to the state as of the factory shipment.

setdefaults : XSCF clear : unmount filesystem start

dbs[282]: NOTICE: received signal: 15

setdefaults : XSCF clear : unmount /hcp0/linux

...

setdefaults : XSCF clear : unmount /hcpcommon/firmtmp -- complete

setdefaults : XSCF clear : unmount filesystem complete

setdefaults : XSCF clear : end

setdefaults : complete

Please turn off the breaker after XSCF halt.

The system is going down NOW !!

Please stand by while rebooting the system.

Restarting system.

XSCF uboot 01950000 (Apr 15 2007 - 11:08:18)

SCF board boot factor = a040

DDR Real size: 512 MB

DDR: 480 MB

XSCF BOOT STOP (recover by NFB-OFF/ON)

XSCF>

restoredefaults -c factory

WARNING:

If this system does not have OPNL, this command will set all the user

settable XSCF configuration parameters to their default value as they

were set when the system was shipped out.

Furthemore, this command will delete all logs on both XSCFUs.

Check the man page of this command before you run it.

Continue?[yes/no](default no):

yes

You must check the following points.

1. Have the ability to powercycle the system.

2. Have access to the serial console and hold the serial console of the

XSCFU to confirm the completion of the command.

If you answer "yes" this command will HALT the XSCFU when it compltetes.

You will need to powercycle the system after the XSCF BOOT STOP.

Do you really want to continue?

Continue?[yes/no](default no):

yes

The initialization of XSCFU will be started.

XSCFU : all data clear

OPNL : all data clear (exclude SYSTEM ID data)

Содержание SPARC Enterprise M3000

















































































































































































































































































































































































































































































































































































Результаты поиска

Содержание SPARC Enterprise M3000

Отзывы:

Fujitsu SPARC Enterprise M3000, Справочное руководство Xscf, Страница: 167 / 560

Результаты поиска

Содержание SPARC Enterprise M3000

Отзывы: