Fujitsu SP-1130Ne Скачать руководство пользователя страница 95 | Manualshive

Страница: 95 / 143

background image

Cannot Connect the Scanner and a Computer with the Network

Check the following points

●

Is the scanner connected to a network device (such as a switch, a hub, or a router) via a LAN cable?
(page 95)

●

Is the network device (such as a switch, a hub, or a router) turned on? (page 95)

●

Is the firmware version for the network device the latest? (page 96)

●

Is the computer connected to a network device (such as a switch, a hub, or a router)? (page 96)

●

Did you configure the settings related to communication conditions on a network device (such as a
switch, a hub, or a router)? (page 96)

●

Are there any security limitations in the network? (page 96)

●

Is the network stable? (page 96)

●

Did you select the scanner in Scanner Selection Tool? (page 97)

●

Is the communication status between the scanner and the computer stable? (page 97)

●

Is the scanner connected to another computer? (page 98)

●

Is the scanner's IP address correct? (page 98)

●

Is the IP address of the scanner used for other communication devices? (page 98)

●

Is the correct scanner name set for the image scanning application? (page 98)

If the problem still persists, check each item in

Before You Contact the Scanner Service Provider (page

first, then contact the distributor/dealer where you purchased this product. Refer to the contact

information in the Contact List if supplied with this product, or refer to the contact information in the
Contact for Inquiries section if provided in Safety Precautions supplied with this product, and then make an
inquiry.

●

Is the scanner connected to a network device (such as a switch, a hub, or a router) via a LAN cable?

Solution

Connect the scanner to a network device (such as a switch, a hub, or a router) via a LAN cable. Also,
connect the LAN cable properly.
When the LAN cable is connected properly, take the following measures:

●

Replace the LAN cable.

●

Change the port on the network device, which the LAN cable is connected to.

●

Change the transmission method for the network device to "full-duplex" or "half-duplex".

●

Is the network device (such as a switch, a hub, or a router) turned on?

Solution

Turn on the network device (such as a switch, a hub, or a router).
Also, check that there is no error or malfunction on the network device.
For errors that occur on the network device, refer to the manual of your network device.

Troubleshooting

95

«
...
93
94
95
96
97
...
»

Содержание SP-1130Ne
















































































































































Отзывы:

Нет отзывов

Похожие инструкции для SP-1130Ne

Бренд: Xerox Страницы: 14

Бренд: Wasp Страницы: 284

Бренд: Radio Shack Страницы: 16

Бренд: Dynamic Страницы: 77

Бренд: GRAPHTEC Страницы: 57

Бренд: Penpower Technology Страницы: 29

WorldPenScan Series

Бренд: Penpower Technology Страницы: 34

Бренд: Penpower Technology Страницы: 48

Бренд: Penpower Страницы: 58

Бренд: Autel Страницы: 57

Бренд: 3D Histech Страницы: 22

Бренд: HandHeld Страницы: 57

Бренд: Radio Shack Страницы: 17

Бренд: Magtek Страницы: 41

Бренд: Uniden Страницы: 28

Бренд: nedis Страницы: 5

Бренд: Unitech Страницы: 34

Color Image Reader-F1

Бренд: Canon Страницы: 111

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды