Fujitsu PRIMERGY S60 Скачать руководство пользователя страница 57

Страница: 57 / 99

U41221-J-Z156-1-74

Plug-in Board Modules

The FFx-RAID Controller Module

LED

Description

DAC DEVICE

ACTIVITY

(green)

DAC HOST

ACTIVITY

(green)

OFF

No FC channel activity on the host side

FC channel activity on the host side

OFF

No FC channel activity on the device side

FC channel activity on the device side

Table 9: FFx-RAID Controller Module: FC channel Activity Indicators

LED

Description

DAC (5); GBIC (6);

HSSDC (3)

NODE STATUS

(yellow/green)

green

yellow

OFF

Module not inserted or not powered

OFF

Full Operation: node in the loop active

OFF

Node not in the loop (generally). Possible causes
on GBICs:

GBIC HW-Error status signals active:
RX_LOS, i. e. the received signal is not valid, or
TX_FAULT, i. e. sender works not correctly

OFF

flashing

0.5 sec.

Node disabled from Service Processor (RSB)

Module OK; missing or corrupted data

flashing between green

and yellow

approx. 0.5 sec.

Table 10: FFx-RAID Controller Module: Node Status Indicators

Содержание PRIMERGY S60




































































































Результаты поиска

Содержание PRIMERGY S60

Отзывы:

Fujitsu PRIMERGY S60, Руководство пользователя, Страница: 57 / 99

Результаты поиска

Содержание PRIMERGY S60

Отзывы: