Fujitsu PRIMERGY RX330 S1 Скачать руководство пользователя страница 67

Страница: 67 / 94

RX330 S1

Operating manual

Troubleshooting and tips Drives reported as “dead” when starting system

7.9

Drives reported as “dead” when starting
system

This error message can occur when the onboard SAS controller has RAID
functionality or the server is equipped with a PCI RAID controller.

RAID controller configuration incorrect

Check and correct the settings for the drives using the RAID controller utility.

Further information is provided in the manual for the RAID controller.

7.10

Added drive reported as defective

RAID controller is not configured for this drive

The drive was probably installed when the system was switched off.

Reconfigure the RAID controller for the drive using the corresponding utility.
Information is provided in the documentation for the RAID controller.

Remove and reinstall the drive while the system is switched ON.

If the drive continues to be reported as defective, then replace it (see

“Installing/removing the HDD module” on page 77

and

“Removing the HDD

module” on page 79

7.11

Error message on screen

The meaning of the error message is explained in the manual for the

BIOS-Setup

and in the documentation for the relevant components and programs on the
PRIMERGY

ServerBooks

DVD.

Содержание PRIMERGY RX330 S1































































































Результаты поиска

Содержание PRIMERGY RX330 S1

Отзывы:

Fujitsu PRIMERGY RX330 S1, Руководство по эксплуатации, Страница: 67 / 94

Результаты поиска

Содержание PRIMERGY RX330 S1

Отзывы: