Fujitsu PRIMERGY RX330 S1 Скачать руководство пользователя страница 41

Страница: 41 / 94

RX330 S1

Operating manual

Hardware installation

Installing/removing the server in/from the rack

Installing the telescopic rail with variable support

Figure 5: Fit the left telescopic rail in the PRIMECENTER/DataCenter Rack

Position the left-hand rail (1) in the support bracket with the vertical lug (a)
in the middle square catch.

Press the left rail together until its front end passes behind the front left
support upright (2), then release.

Secure the rail on the front left support upright (3) and the support bracket
in the rack (4) with two (M5) screws each.

Repeat the steps with the right telescopic rail (to be secured to the right
support uprights).

Fit the PRIMECENTER/DataCenter Rack cable management as described
in the technical manual for the rack.

Insert the server (see the

“Inserting the server” on page 43

section).

Route the cables once the server has been inserted, as described in the
Technical Manual for the rack in question.

Содержание PRIMERGY RX330 S1































































































Результаты поиска

Содержание PRIMERGY RX330 S1

Отзывы:

Fujitsu PRIMERGY RX330 S1, Руководство по эксплуатации, Страница: 41 / 94

Результаты поиска

Содержание PRIMERGY RX330 S1

Отзывы: