Fujitsu PRIMERGY RX200 S3 Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 57

background image

RX200 S3

Options Guide

39

Controllers in Non-Hot-Plug PCI Slots

Installing controllers

8.1

Installing controllers

Ê

Open the server as described in the

chapter “Preparation” on page 17

Removing the riser card holder

Figure 22: Removing the riser card holder

Ê

Grasp the riser card at the two green points labeled with “LIFT UP” and pull
it up and out.

Installing a controller

Ê

Please read the documentation supplied with the controller.

Ê

Plug any necessary cables onto the controller.

Ê

Remove the slot cover from the riser card holder.

I

Keep the slot cover for future use. If you remove the controller, you
must reinstall the slot cover to comply with EMC regulations (regula-
tions on electromagnetic compatibility) and to satisfy cooling require-
ments and fire protection measures.

«
...
37
38
39
40
41
...
»

Содержание PRIMERGY RX200 S3


























































Отзывы:

Нет отзывов

Похожие инструкции для PRIMERGY RX200 S3

Univerge SV8100

Бренд: NEC Страницы: 78

Univerge SV8100

Бренд: NEC Страницы: 186

Univerge SV8100

Бренд: NEC Страницы: 150

Univerge SV8100

Бренд: NEC Страницы: 52

Бренд: IBM Страницы: 438

SUPERSERVER 6021F

Бренд: Supermicro Страницы: 116

Бренд: 3onedata Страницы: 4

Бренд: IBM Страницы: 56

System x3350 Type 4192

Бренд: IBM Страницы: 84

Бренд: Hawking Страницы: 40

Бренд: Kontron Страницы: 110

Бренд: IBM Страницы: 110

Бренд: Fibrenetix Страницы: 17

Бренд: TerraMaster Страницы: 13

Бренд: Goonas Страницы: 13

ConnectPort LTS 16

Бренд: Digi Страницы: 169

Бренд: QNAP Страницы: 58

MultiAccess MULTIACCESS MA30120

Бренд: Multitech Страницы: 179

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды