Fujitsu PRIMEQUEST 1000 Series Скачать руководство пользователя страница 262

Страница: 262 / 344

B.1

Manually Installing PSA (Linux: Red Hat Enterprise Linux)

This section describes how to manually install PSA in Linux (Red Hat Enterprise Linux).

Remarks

Be sure to install PSA for PRIMEQUEST 1800E. Otherwise, the following restrictions apply.

- I/O (e.g., PCI Express card, hard disk) failure notification and trap notification to the administrator are

disabled.

- Failure notification using symptom detection and trap notification to the administrator are disabled.

- Threshold exceeded in S.M.A.R.T. monitoring of HDDs

- Operations management software cannot collect information on the partition side.

- Even under an REMCS agreement, no software errors are reported.

- Hot maintenance of hard disks is disabled. The partition must be stopped for maintenance.

- PRIMECLUSTER linkage is disabled.

B.1.1

Installation flow

For details on how to install PSA, see

CHAPTER 4 Installing the Operating System and Bundled Software

. For

details on how to configure PSA, see

B.1 Manually Installing PSA (Linux: Red Hat Enterprise Linux)

Remarks

- After changing the MMB IP address on a partition or the management LAN IP address,

restart PSA. Otherwise, a display error may occur in the [PSA] window of the Web-UI. Moreover, PSA

would not be able to report any detected errors.

- If you use SVIM to install the operating system, you need not manually install PSA. However, after

installation with SVIM, you will need to check and make settings according to

B.1.2 Checks before PSA

installation

and

B.1.6 Settings after PSA installation

B.1.2

Checks before PSA installation

This section describes the checks to make before PSA installation.

Confirming PSA-to-MMB communication LAN settings

Confirming management LAN settings

Confirming the functions required for PSA operation

Confirming the status of the iptables service

Confirming PSA-to-MMB communication LAN settings

For details on how to confirm PSA-to-MMB communication LAN settings, see

6.2.1 Configuring the PSA-to-

MMB communication LAN

and

6.2.7 Setting the management LAN IP address

Confirming management LAN settings

For details on how to confirm management LAN settings, see

6.2.2 Confirming management LAN settings

Confirming the functions required for PSA operation

The following table lists the packages required for PSA operation. Execute the rpm command to confirm the

installation of each package.

The packages that must be installed depend on the CPU architecture (x86/x64).

PRIMEQUEST 1000 Series Installation Manual
APPENDIX B Manual PSA Installation and Uninstallation

234

C122-E107-09EN

Содержание PRIMEQUEST 1000 Series

























































































































































































































































































































































Результаты поиска

Содержание PRIMEQUEST 1000 Series

Отзывы:

Бренды по названию

Популярные бренды

Fujitsu PRIMEQUEST 1000 Series, Руководство по установке

Результаты поиска

Содержание PRIMEQUEST 1000 Series

Отзывы:

Бренды по названию

Популярные бренды