manualshive.com logo in svg

Fujitsu PRIMEQUEST 1000 Series, Руководство по установке

Серия серверов Fujitsu PRIMEQUEST 1000 - надежное решение для вашего бизнеса. Получите бесплатное Руководство пользователя для этого продукта на manualshive.com. Загрузите его сейчас! Надежность, производительность и удобство использования в одном устройстве. Не упустите шанс улучшить работу вашей компании с помощью Fujitsu PRIMEQUEST 1000 Series.

Поделиться
Скачать
background image

6.2.2

 Confirming management LAN settings

Make network settings for the management LAN. If necessary, also configure any duplication with bonding or

PRIMECLUSTER GLS, for example.

After completing the above network settings for the management LAN, perform the operations described in 

6.2.4

Checking the firewall function (opening ports)

 and 

6.2.7 Setting the management LAN IP address

.

 

Note

In the PRIMEQUEST environment, it is necessary to specify OFF for the STP function of the switch that connects

to the management LAN used for communication with the MMB.

 

6.2.3

 Confirming SELinux function settings

This section describes the SELinux settings and how to confirm them.

Other OS settings

- For RHEL5

If the partition OS with PSA installed is running RHEL5, disable the SELinux functions. When installing

PSA, the SELinux functions are automatically disabled. Confirm that the SELinux functions are disabled. If

the SELinux functions are enabled, disable them.

- For RHEL6.0/RHEL6.1

If the partition OS with PSA installed is running RHEL6.0/RHEL6.1, disable the SELinux functions. When

installing PSA, the SELinux functions are not automatically disabled. Check the SELinux function setting.

If the SELinux functions are enabled, disable them.

- For RHEL6.2 or later

If the partition OS with PSA installed is running RHEL6.2 or later, it operates irrespective of whether the

SELinux functions are enabled or disabled.

 

The procedure for confirming the SELinux function setting and disabling the SELinux functions is as follows.

Confirm that the following command displays "disabled" when operating the system with the SELinux functions

disabled. If the command displays anything other than "disabled," disable the functions by editing the config file

(/etc/selinux/config).

 

Confirming settings

#cd /etc/selinux/

#more config

.....

.....

SELinux=disabled   

←

 Confirm this.

 

Changing settings

# vi /etc/selinux/config

.....

.....

SELinux=disabled   

←

 Edit this.

 

PRIMEQUEST 1000 Series Installation Manual
CHAPTER 6 Work after Operating System Installation (PRIMEQUEST 1800E)

134

C122-E107-09EN

Содержание PRIMEQUEST 1000 Series

























































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PRIMEQUEST 1000 Series

GE Mini Field Agent User Manual preview
Mini Field Agent
Бренд: GE Страницы: 87
Raritan DOMINION SX - Quick Setup Manual preview
DOMINION SX -
Бренд: Raritan Страницы: 4
Roland MSL-15 Owner'S Manual preview
MSL-15
Бренд: Roland Страницы: 12
LogLogic LX 1010 Quick Start Manual preview
LX 1010
Бренд: LogLogic Страницы: 30
hilscher CIFX 104 User Manual preview
CIFX 104
Бренд: hilscher Страницы: 154
Baicells EG2013B-M11 User Manual preview
EG2013B-M11
Бренд: Baicells Страницы: 10
ICP DAS USA iWSN-200E Quick Start Manual preview
iWSN-200E
Бренд: ICP DAS USA Страницы: 8
Penguin Edge MVME2500 Quick Start Manual preview
MVME2500
Бренд: Penguin Edge Страницы: 2
AMX AXB-PSCV Dimensional Drawing preview
AXB-PSCV
Бренд: AMX Страницы: 1
Fast FV3000-W2K Instruction Manual preview
FV3000-W2K
Бренд: Fast Страницы: 66
IMC Networks Wireless Outdoor Bridge XI-1500-IH Quick Installation Manual preview
Wireless Outdoor Bridge XI-1500-IH
Бренд: IMC Networks Страницы: 13
PairGain T1L2F10A Manual preview
T1L2F10A
Бренд: PairGain Страницы: 76
Atmel SAMA5D31-EK User Manual preview
SAMA5D31-EK
Бренд: Atmel Страницы: 123
ST X-NUCLEO-AMICAM1 User Manual preview
X-NUCLEO-AMICAM1
Бренд: ST Страницы: 18
Tripp Lite B078-001-USB Specification preview
B078-001-USB
Бренд: Tripp Lite Страницы: 2
Maco RUSTICO 13321 Installation Instructions Manual preview
RUSTICO 13321
Бренд: Maco Страницы: 8
Extron electronics StudioStation 100 Installation Manual preview
StudioStation 100
Бренд: Extron electronics Страницы: 4
Nedap Luxon Bridge Installation Manual preview
Luxon Bridge
Бренд: Nedap Страницы: 3

Бренды по названию

Популярные бренды

Загрузить еще бренды