Fujitsu MHJ2181AT Скачать руководство пользователя | Manualshive

Страница: 165 / 227

background image

Interface

5-92

C141-E088-03EN

7)

If DSTROBE is negated, the device shall assert DSTROBE within t

LI

after the host has asserted STOP. No data shall be transferred during this
assertion. The host shall ignore this transition on DSTROBE.
DSTROBE shall remain asserted until the Ultra DMA burst is
terminated.

8)

If the host has not placed the result of its CRC calculation on DD (15:0)
since first driving DD (15:0) during (6), the host shall place the result of
its CRC calculation on DD (15:0) (see 5.5.5).

9)

The host shall negate DMACK- no sooner than t

MLI

after the device has

asserted DSTROBE and negated DMARQ and the host has asserted
STOP and negated HDMARDY-, and no sooner than t

DVS

after the host

places the result of its CRC calculation on DD (15:0).

10) The device shall latch the host's CRC data from DD (15:0) on the

negating edge of DMACK-.

11) The device shall compare the CRC data received from the host with the

results of its own CRC calculation. If a miscompare error occurs during
one or more Ultra DMA bursts for any one command, at the end of the
command the device shall report the first error that occurred (see 5.5.5).

12) The device shall release DSTROBE within t

IORDYZ

after the host negates

DMACK-.

13) The host shall not negate STOP no assert HDMARDY- until at least t

ACK

after negating DMACK-.

14) The host shall not assert DIOR-, CS0-, CS1-, DA2, DA1, or DA0 until at

least t

ACK

after negating DMACK.

b)

Host terminating an Ultra DMA data in burst

The following steps shall occur in the order they are listed unless otherwise
specifically allowed (see 5.6.4.6 and 5.6.4.2 for specific timing
requirements):

1)

The host shall not initiate Ultra DMA burst termination until at least one
data word of an Ultra DMA burst has been transferred.

2)

The host shall initiate Ultra DMA burst termination by negating
HDMARDY-. The host shall continue to negate HDMARDY- until the
Ultra DMA burst is terminated.

3)

The device shall stop generating DSTROBE edges within t

RFS

of the host

negating HDMARDY-.

4)

If the host negates HDMARDY- within t

SR

after the device has generated

a DSTROBE edge, then the host shall be prepared to receive zero or one
additional data words. If the host negates HDMARDY- greater than t

SR

after the device has generated a DSTROBE edge, then the host shall be
prepared to receive zero, one or two additional data words. The
additional data words are a result of cable round trip delay and t

RFS

timing

for the device.

«
...
163
164
165
166
167
...
»

Содержание MHJ2181AT




































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MHJ2181AT

Бренд: Oki Страницы: 16

Бренд: Qualstar Страницы: 205

RX343-S BLK/SLV

Бренд: Rosewill Страницы: 2

Бренд: Weka Страницы: 28

Бренд: Performance Tool Страницы: 2

Бренд: Aegis Страницы: 1

Бренд: DFI Страницы: 28

Бренд: SATA Страницы: 8

CHEETAH NS 10K.2 ST3450802SS

Бренд: Seagate Страницы: 80

Бренд: TerraMaster Страницы: 13

DIGIARRAY DA-4000E

Бренд: Digiever Страницы: 9

Бренд: HOLZMANN MASCHINEN Страницы: 16

Бренд: HOLZMANN MASCHINEN Страницы: 20

Бренд: Sonnet Страницы: 6

Бренд: Newer Technology Страницы: 20

miniStack Classic

Бренд: Newer Technology Страницы: 24

Бренд: Backyard Страницы: 63

STOR-912-G-W-1RH

Бренд: Vestil Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды