Chapter 5 Troubleshooting
IP-900E/IP-900D series
56
No. Class
Status
Description
Recommended
action
12.
Has the monitor on the receiving
side been powered on?
Check the power and operation of the
monitor.
13.
Has the device on the receiving
side been powered on?
Check the power and operation of the
device on the receiving side.
14.
Is the device on the receiving side
and monitor correctly connected?
Check connections between the device on
the receiving side and the monitor.
15.
Did the device on the receiving
side generate an alarm?
If an alarm is generated, refer to the relevant
operating manuals on the receiving side, and
take appropriate corrective action.
16.
No image can
be output on the
receiving side
(black screen).
Does a color bar or gray screen
appear on the receiving side if
image input of the device is set to
non-input? (Since this operation
generates an alarm, obtaining the
system administrator’s approval
before conducting this test.)
If the blue screen is displayed, the receiving
side can be assumed to be operated
normally.
Verify that the correct image is input in the
device.
17.
Is the RDY LED blinking?
The hardware system is operating while the
RDY LED is blinking. Wait until the
LED remains on.
18.
Is the RDY LED turned on orange?
The device is started in the maintenance
mode.
Reboot the device.
19.
Is the ALM LED blinking?
ALM LED blinks when IP address
obtaining is on going or releasing. Check IP
address setting (For more information, refer
the Software User’s Guide).
20.
Has the encoder started encoding?
Set the encoder to start encoding.
21.
Has the decoder started decoding?
Set the decoder to start decoding.
22.
Is the streaming setting correct?
Make the correct streaming setting of this
device and the encoder by referring to the
Software User’s Guide.
23.
Blue/gray
screen is output.
Is the network normal?
Refer to “Network” in this table.
24.
Image/audio
output is
distorted.
Is packet loss occurring on the
decoder?
If so, confirm the followings.
・
Is system bit rate exceeding connected
network capacity?
・
Are FEC/ARQ settings in this device and
the opposed device correct?
・
Are the network device and LAN port
settings (AUTO, Full/Half-duplex, etc) the
same?
25.
Is the setting of encoder PAL when
the camera or display is NTSC
type?
Change encoder setting from PAL to NTSC.
(Check decoder setting too.)
26.
Vi
de
o
The image
output is
distorted.
(Analog input
case)
Is the setting of encoder NTSC
when the camera or display is PAL
type?
Change encoder setting from NTSC to PAL.
(Check decoder setting too.)
Содержание IP-900 II D
