manualshive.com logo in svg

Fujitsu Inverter Halcyon ASU24CL, Руководство по установке

Поделиться
Скачать
Fujitsu Inverter Halcyon ASU24CL Скачать руководство пользователя страница 14

WIRED REMOTE CONTROL UNIT

INSTALLATION MANUAL

(PART NO. 9315757012)

ENGLISH

BEFORE INSTALL WIRED REMOTE CONTROL UNIT

•

The wired remote control unit is an option. It isn't included in main body of air-conditioner.

•

When you use wired remote control unit, some functions may not be used.

•

Please use the recommended wired remote control unit.

(Before installing, Please read the FEATURES AND FUNCTIONS section of OPERATING MANUAL to confirm the
concerned contents.)

 CAUTION

(1) Before installing, be sure to disconnect all power supply.

(2) Don't touch the heat exchanger.

(3) During installing or removing operation, be sure not to have wire catched by parts or draw it hard. Or it

may result troubles to the air-conditioner.

(4) Avoid place in direct sunlight.

(5) Select place that will not be affected by the heat from a stove, etc.

(6) Insure the length of wire is not over the recommended maximum length.

(7) Before setting up the wired remote control unit, please confirm whether air-conditioner can receive the

signal.

1.  FRONT PANEL, CONTROL BOX COVER AND DISPLAY CASE REMOVAL

(1) Refer to “FRONT PANEL REMOVAL AND INSTALLATION” to remove the front panel.
(2) Remove screws then remove the control box cover.

(3) Remove the display case and connector.

2.  CONNECTING TO CONTROL UNIT OF WIRE

(1) Pass the connector from the hole in the back.
(2) Connect the wire of wired remote control unit to the board of Control unit.
(3) Hook the wire to the rib.

(4) Use wire clamper and screw to fasten the wire.

3.  FRONT PANEL, CONTROL BOX COVER AND DISPLAY CASE

INSTALLATION

Install front panel, control box cover and display case by the reverse proce-
dures as stated in “1.FRONT PANEL, CONTROL BOX COVER AND DISPLAY
CASE REMOVAL”..

control box
cover

screw

connector

display case

wire clamper

screw

screw

wire of
wired
remote
control
unit

original wire of
control unit

conduit holder

wire clamper

connect the
wire

rib

hole

Содержание Inverter Halcyon ASU24CL















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды