En-20
Notes
Possible temperature setting ranges in the operation
•
mode are as follows:
Cool, Dry, Auto ...............
18 to 30 °C (64 to 88 °F)
Heat ...............................
16 to 30 °C (60 to 88 °F)
If the temperature out of the Set temp. range limitation
•
is set, it will be reset at the nearest temperature within
the range. However, the adjusted temperature value
in this setting will not be corrected automatically.
(7) Select [Zone (single)] (individual setting of zone control)
or [Zone (group)] (simultaneous setting of zone control)
as follows:
Individual setting of zone control):
Select [Zone (single)] with the [Cursor button (Up/
Down)]. Then press the [Cursor button (Right)] to move
the cursor to next setting item.
1
Weekly
1
Day
Time
End
Su Mo
5 00
On
Weekly timer setting
Time 8
Time 2
Mo 10:00
Cancel:
OK:
Heat
20
°C
Zone (single)
Sensor:
Select the room-temperature sensor with the [Cur-
sor button (Up/Down)]. Then press the [Cursor button
(Right)] to move the cursor to next setting item.
1
Weekly
1
Day
Time
End
Su Mo
5 00
On
Weekly timer setting
Time 8
Time 2
Mo 10:00
Cancel:
OK:
Heat
20
°C
Zone (single) Sensor
Zone 1
Secondary RC
Zone 2
Zone 3
Zone 4
Zone 5
Zone 6
Zone 7
Zone 8
Select applicable zone name with the [Cursor button
(Left/Right)], and press the [Cursor button (Up/Down)]
to mark a check.
Check-marked: The zone is air-conditioned.
Blank: The zone is not air-conditioned.
1
Weekly
1
Day
Time
End
Su Mo
5 00
On
Weekly timer setting
Time 8
Time 2
Mo 10:00
Cancel:
OK:
Heat
20
°C
Zone (single) Sensor: Secondary RC
Zone 1
Zone 2
Zone 3
Zone 4
Zone 5
Zone 6
Zone 7
Zone 8
After you select all the applicable zones, press the
[Enter button] to complete the individual setting of zone
control.
Notes
When you set “On timer”, you need to set all of
•
operating mode, temperature, room-temperature
sensor, and applicable zone(s).
Without these configurations, the timer will not work.
Depending on the initial setup in the installation, there
•
is a case that at least one zone need to be selected.
In that case, following message is displayed on the
screen, and you need to put a check mark at least one
zone
XXXXXX
XXXXXX
One zone must be open at all times.
Simultaneous setting of zone control):
Select [Zone (group)] with the [Cursor button (Up/
Down)]. Then press the [Cursor button (Right)] to move
the cursor to next setting item.
1
Weekly
1
Day
Time
End
Su Mo
5 00
On
Weekly timer setting
Time 8
Time 2
Mo 10:00
Cancel:
OK:
Heat
20
°C
Zone (group)
Select the applicable group with the [Cursor button (Up/
Down)].
1
Weekly
1
Day
Time
End
Su Mo
5 00
On
Weekly timer setting
Time 8
Time 2
Mo 10:00
Cancel:
OK:
Heat
20
°C
Zone (group)
Day
To complete the simultaneous setting of zone control,
press the [Enter button].
1
Weekly
1
Day
Time
End
Su Mo
5 00
On
Weekly timer setting
Time 8
Time 2
Mo 10:00
Back:
Setting:
Heat
20
°C
Zone (group)
Day
(8) When setting the other days of the week continually,
perform procedures in step 4 and 5.
9374379866_OM_EN.indd 20
17/12/2014 13:19:30
Содержание ARTC72LATU
Страница 40: ......