Fujitsu AOTG30LATL Скачать руководство пользователя

Страница: 29 / 78

Detective Actuators:

Detective details:

Forecast of Cause :

1. Connector connection failure 2. Thermistor failure 3. Coil failure 4. 4-way valve failure

5. Main PCB failure

Check Point 1 : Check connection of Connector

Check if connector is removed.

Check erroneous connection.

Check if thermistor cable is open.

>> Upon correcting the removed connector or mis-wiring, reset the power.

Check Point 3 : Check the solenoid coil and 4-way valve

02-26

[ Solenoid coil ]

Remove CN111 from PCB and check the resistance value of coil.

Resistance value is about 1.4k

>> If it is Open or abnormal resistance value, replace Solenoid Coil.

[ 4-way valve ]

Check each piping temperature,

and the location of the valve by the temperature difference.

>> If the value location is not proper, replace 4-way valve.

Check Point 4 : Replace Main PCB

If Check Point 1- 3 do not improve the symptom, replace Main PCB.

Check Point 2 : Check thermistor of Indoor unit

Isn’t it fallen off the holder?

Is there a cable pinched?

>> Check characteristics of thermistor, (Refer to Trouble shooting 5,6),

If defective, replace the thermistor.

Indoor Unit Controller PCB Circuit

Heat Exchanger Temperature Thermistor

Room Temperature Thermistor

4-way valve

When the indoor heat exchanger temperature is compared with

the room temperature, and either following condition is detected

continuously two times, the compressor stops.

Cooling or Dry operation

[Indoor heat exchanger temp.] - [Room temp.] > 20degC

Heating operation

[indoor heat exchanger temp.] - [Room temp.] < -14degC

If the same operation is repeated 5 times,

the compressor stops permanently.

Trouble shooting 23

OUTDOOR UNIT Error Method:

4-Way Valve Error

Indicate or Display:

Refer to error code table.

Содержание AOTG30LATL















































































Результаты поиска

Содержание AOTG30LATL

Отзывы:

Похожие инструкции для AOTG30LATL

Бренды по названию

Популярные бренды

Fujitsu AOTG30LATL, Инструкция по эксплуатации

Результаты поиска

Содержание AOTG30LATL

Отзывы:

Похожие инструкции для AOTG30LATL

Бренды по названию

Популярные бренды