Fujitsu AOTG30LATL Скачать руководство пользователя

Страница: 27 / 78

02-24

Trouble shooting 18

OUTDOOR UNIT Error Method:

Detective Actuators:

Detective details:

Forecast of Cause:

Check Point 3 : Check Outdoor unit fan motor

Outdoor Unit Fan Motor 1 Error

Outdoor unit Main PCB

Outdoor unit fan motor

1. Fan rotation failure 2. Motor protection by surrounding temperature rise 3. Main PCB failure

4. Outdoor unit fan motor failure

Check Point 1 : Check rotation of Fan

Rotate the fan by hand when operation is off.

(Check if fan is caught, dropped off or locked motor)

>>If Fan or Bearing is abnormal, replace it.

Check Outdoor unit fan motor.

(PARTS INFORMATION 5)

>>If Outdoor Fan Motor is abnormal, replace Outdoor fan motor and Main PCB.

Check Point 4 : Check Output Voltage of Main PCB

Check outdoor unit circuit diagram and the voltage. (Measure at Main PCB side connector)

If the voltage is not correct, replace Main PCB.

When outdoor fan rotation speed is less than 100rpm in 20 seconds

after fan motor starts, fan motor stops.

After fan motor restarts, if the same operation within 60sec is repeated

3 times in a row, compressor and fan motor stops.

If and repeats 5 times in a row, compressor and fan motor stops

permanently.

Read wire DC voltage

Red - Black

240 - 400V

White - Black

15 1.5V

CN800

BLACK
WHITE

YELLOW

BROWN

RED

FAN MOTOR

Check Point 2 : Check ambient temp. around motor

Check excessively high temperature around the motor.

(If there is any surrounding equipment that causes heat)

>>Upon the temperature coming down, restart operation.

Indicate or Display:

Refer to error code table.

Содержание AOTG30LATL















































































Результаты поиска

Содержание AOTG30LATL

Отзывы:

Похожие инструкции для AOTG30LATL

Бренды по названию

Популярные бренды

Fujitsu AOTG30LATL, Инструкция по эксплуатации

Результаты поиска

Содержание AOTG30LATL

Отзывы:

Похожие инструкции для AOTG30LATL

Бренды по названию

Популярные бренды