background image

En-7

 7.  ENERGY SAVING OPERATIONS

7.1. Economy operation

It saves more electricity than other operation modes by changing the set 
temperature to a moderate setting.

Press 

 to activate/deactivate the Economy 

operation.

[   ] indicator on the indoor unit will turn on.

Operation 

mode

Room temperature

Cooling/Dry

Few degrees higher than the set temperature

Heating

Few degrees lower than the set temperature

NOTES:

•  In the Cooling, Heating, or Dry mode, the maximum output of this 

operation is approximately 70 % of usual operation.

•  This operation cannot be performed during the temperature 

monitoring by the Auto mode.

 7.2.  Human sensor for energy saving

 

WARNING

•  Do not use this function when there are only infants, 

children, elderly, or sick persons in the room.

 

CAUTION

•  Do not use this function in server rooms or other 

places where there is no one in the room.

•  Do not place large objects near the human sensor. 

Also keep heating units outside the sensor’s detection 

area.

When no one is in the room, the air conditioner operates moderately to 
prevent waste of electricity.
(This function is activated at the time of purchase.)

To change the setting, press 

 .

While the Energy Saving program is activated, 

 on the 

remote controller display will turn on.

NOTES:

•  The following operations will override the Energy Saving program.

 

- Sleep timer operation

 

- Min. Heat operation

•  The Energy Saving program may not work when the room 

temperature is very di

 erent from the set temperature, such as 

when immediately after starting the operation.

 

Details on Energy Saving program

Human sensor on the indoor unit detects movement of people.
If there is no one in the room for approximately 20 minutes, the 
temperature will be adjusted moderately.
When someone comes back into the room, the air conditioner revert to 
the original settings.

Operation 

mode

Room temperature

(When there is no one there)

Cooling/Dry

Higher than the set temperature (Max. +4 

˚

F (+2 

˚

C))

Heating

Lower than the set temperature (Max. -8 

˚

F (-4 

˚

C))

Auto

Depending on the operating mode (Cooling/ Heating/ 
Dry).

Detection range of Human sensor

90°

22 ft

 (

7 m

22 ft

(7 m

50°

50°

Side view

Top view

NOTES: 

Since Human sensor detects infrared light given out by people, 

the detection may be incorrect in the following situations.

Situations in which the sensor may detect no one in the room, 
even when there is someone there:

•  When the room temperature is high and the di

 erence with people’s 

body temperature is small. (Such as when the temperature is 86 

˚

(30 

˚

C) or higher in summer.)

•  When someone in the room do not move for a long time.
•  When someone is hidden behind a sofa, other furniture, glass, or in 

similar situations.

•  When someone is wearing extremely thick clothing and turn their 

backs on the sensor.

Situations in which the sensor may detect people in the room, even 
when there is no one there

•  When there is a dog or a cat moving around in the room.
•  When wind is moving curtains or plants.
•  When heating units, humidi

fi

 ers, or electric appliances such as 

oscillating electric fans are operating.

 7.3.  Fan control for energy saving

 In the Cooling operation, when the room 
temperature reaches the set temperature, the 
indoor unit fan rotates intermittently to save 
power. (This function is activated at the time of 
purchase.)

To change the setting, use the following 

steps;

1. 

Press   until only the clock is displayed on the remote 

controller display.

2. 

Press down 

 for more than 5 seconds.

The current Fan Control status ( 

 ) is displayed.

3. 

Press 

 to switch between activated ( 

 ) or 

deactivated ( 

 ).

4. 

Press   to send the setting to the indoor unit.

The display will return to the original screen.

NOTES:

 If you do not press any buttons for 30 seconds after 

 is 

displayed, 

 will turn o

 . In this case, repeat the setting from 

step 2.

 6.4. Sleep timer 

1. 

Select Sleep timer in step 2 of "Timer setting procedure".

2. 

Press 

(

)

 to set the time until the operation stops.

Each time you press the button, the time changes as follows:

9H

00M

7H

00M

5H

00M

3H

00M

2H

00M

1H

00M

0H

30M

hours

(30 min.)

•  To deactivate the Sleep timer, press 

 while 

 is shown 

on the remote controller display.
The indicator will disappear.

During the Sleep timer operation, the setting temperature changes as 
the following 

fi

 gure.

In Heating mode

Set 
temperature

Set time

1 hour

Set time

1 hour

1.5 hour

30 min.

2 °F (1 °C) 4°F (2 °C) 6°F (3 °C) 8°F (4 °C)

4°F (2 °C)

2 °F (1 °C)

In Cooling or Dry mode

After the set time has elapsed, the air conditioner operation turns o

 .

9387602098̲OM.indb   7

9387602098̲OM.indb   7

2022/09/26   19:41:40

2022/09/26   19:41:40

Содержание Airstage Wall Series

















Отзывы: