background image

En-4

3.3.1  Single outdoor unit installation

When the upward area is open  

Unit: mm

(1)  Obstacles at rear only

100 or more

(2)  Obstacles at rear and sides only

100 or more

300 or 
more

80 or 
more

(3)  Obstacles at front only

1000 or more

(4)  Obstacles at front and rear only

1000 or more

100 or more

When an obstruction is present also in the upward area  

Unit: mm

(1)  Obstacles at rear and above only

100 or 
more

Max. 
500

1000 or 
more

(2)  Obstacles at rear, sides, and above only

1500 or 
more

80 or 
more

100 or more

300 or 
more

3.3.2  Multiple outdoor unit installation

• Provide at least 100 mm of space between the outdoor units if multiple units are 

installed.

• When routing the piping from the side of an outdoor unit, provide space for the piping.

When the upward area is open

  Unit: mm

(1)  Obstacles at rear only

300 or 
more

(2)  Obstacles at front only

1500 or more

(3)  Obstacles at front and rear only

500 or more

1500 or more

When an obstruction is present also in the upward area

  Unit: mm

(1)  Obstacles at rear and above only
• Up to 3 units can be installed side by side.
• When 4 units or more are arranged in a line, provide the space as shown below.

1500 or 
more

500 or 
more

Max. 
300

1500 or 
more

3.3.3  Outdoor units installation in multi row

*  The following settings are not recommended in case of cooling by a low outside tem-

perature.  Unit: mm

(1)  Single parallel unit arrangement

(2)  Multiple parallel unit arrangement

100 or 
more

600 or more

1000 or more

2000 or 
more

500 or 
more

600 or more

1500 or more

3000 or 
more

3.4.  Transporting the unit

 WARNING

Do not touch the fins. Otherwise, personal injury could result.

 CAUTION

When carrying the unit, hold the handles on the right and left sides and be careful.
If the outdoor unit is carried from the bottom, hands or fingers may be pinched.

Hoisting method

• When hoisting the outdoor unit, hook the rope on the outside of the foot as shown in the 

figure.

• Use sufficiently strong rope to bear the unit’s weight.
• Place protective board or filler cloth at the place where the cabinet may come into 

contact with the rope to prevent damages. Without using them, the cabinet may be dam-
aged or deformed.

• The center of gravity of the outdoor unit is shifted to the right. Be careful not to tilt to the 

heavy side causing it to fall.

• To prevent an accident caused by the unit swinging or falling down, do not apply any 

impact to the unit when it is hanging.

• When hoisting, do not hook the rope to the thermistor holder on the back of the outdoor 

unit.

Protective 
boards

Foot

Light 
side

Heavy 
side

700 to 
1000 mm

Product mass (kg)

AJ*072LELAH

170

AJ*090LELAH

177

AJ*108LELAH

178

AJ*126LELAH

213

AJ*144LELAH

213

AJ*162LELAH

217

Lifting by forklift

• When using the forklift to lift the unit, pass 

the forklift arms through the opening space 
of the wooden delivery pallet.

• Be careful not to damaged.

Wooden delivery 
pallet

Carrying by hand

• Carry slowly in the manner 

as shown on “Fig. B” hold-
ing the handles “Fig. A” 
in right and left sides. (Be 
careful not to touch with 
hands or objects.)

• Be sure to hold the 

handles on the sides of 
the unit. Otherwise, the 
suction grilles on the 
sides of the unit may be 
deformed.

Handle

Handle

Handle

Fig. A

Fig. B

9380545347-01_IM.indb   4

9380545347-01_IM.indb   4

11/29/2019   8:49:51 AM

11/29/2019   8:49:51 AM

Содержание AIRSTAGE AJ 072LELBH Series




















Отзывы: