Fujitsu 24LMAS1 Скачать руководство пользователя страница 10

Страница: 10 / 17

En-10

3.9.2. Knock out holes for wiring

CAUTION

• Be careful not to deform or scratch the panel while opening the knock out holes.

• When cables are routed from the unit, a protection sleeve for the conduits can be

inserted at the knock out hole.

• If you do not use a wire conduit, be sure to protect the wires to prevent the edge of

the knock out hole from cutting the wires.

• It is recommended to apply anti-rust paint to the edge of the knock out hole.

• Knock out holes are provided 2 each in the same size in front, lateral and rear sides.



Wiring procedure

Cable with

conduit

(for connection

cable)

Cable with conduit

(for power cable)

Front connection

Lateral connection

Rear connection

Lock nut

Fix the conduit with the supporters as shown below.

Supporter

Conduit (Power supply cable)

Outdoor unit

30 in

(756 mm)

or less

54 in

(1,360 mm)

or less

54 in

(1,360 mm)

or less

54 in

(1,360 mm)

or less

3.9.3. Wiring method

CAUTION

When connecting the power supply cable, make sure that the phase of the power

supply matches with the phase of the terminal board. If the phases do not match, the

compressor will rotate in reverse and will not be able to compress.



Connection diagrams

Power supply

Outdoor unit

side terminal

Indoor unit
side terminal

Power line

Ground

(Earth)

Ground

(Earth)



Cable preparation

• Keep the ground (earth) wire longer than the other wires.

Ground (Earth)

wire

1-9/16 in (40 mm)

Power supply cable or

Connection cable

2-3/8 in (60 mm)



Wiring procedure

(1) • Remove the tapping screws. (2 places)

• Remove the service cover by pushing downwards.

Service cover

Screws

Direction of the

service cover

removal

(2)

Connect the power supply cable and the connection cable to terminal.

(3) Fasten the power supply cable and connection cable with cable tie.

Terminal blocks

Use the specified

wire type and

connect it securely.

Firmly secure cable tie

so wire terminations will not receive

external stress.

Connection cable

Power supply cable

Indoor

unit

Ground

(Earth)

L1 L2

(4) Secure the cables using the cable tie attached to the base of the valves.

Cable tie

(5) Put the service cover back after completion of the work.

Replace the tapping screws. (2 places)

Service cover

Direction of the

service cover

attachment

9379113069-02_IM.indb 10

6/11/2021 10:26:46 AM

Содержание 24LMAS1


















Результаты поиска

Содержание 24LMAS1

Отзывы:

Похожие инструкции для 24LMAS1

Бренды по названию

Популярные бренды

Fujitsu 24LMAS1, Руководство по установке

Результаты поиска

Содержание 24LMAS1

Отзывы:

Похожие инструкции для 24LMAS1

Бренды по названию

Популярные бренды