Fujitsu Siemens Computers SCENIC Edition X100 Скачать руководство пользователя

Страница: 36 / 65

Troubleshooting and tips

A26361-K678-Z121-1-7619, edition 1

The screen stays blank

If your screen remains blank this may be due to the following:

Monitor is switched off

►

Switch your monitor on.

Power saving has been activated (screen is blank)

►

Press any key on the keyboard.

►

Deactivate the screen saver. Enter the appropriate password.

Brightness control is set to dark

►

Adjust the brightness control. For detailed information, please refer to the operating manual
supplied with your monitor.

Power cable not connected

►

Switch off the monitor and the PC.

►

Check that the monitor power cable is properly connected to the monitor and, depending on
your device configuration level, to the device itself or to a grounded mains outlet.

►

Check that the PC power cable is properly plugged into the PC and grounded mains outlet.

►

Switch on the monitor and the PC.

Monitor cable not connected

►

Switch off the monitor and the PC.

►

Check that the monitor cable is properly connected to the PC and monitor.

►

Switch on the monitor and the PC.

Wrong monitor has been set under Windows 2000

►

Restart the PC.

►

If the message

Starting Windows

appears, press function key

The

Windows 2000 Advanced Options Menu

appears.

►

Select

Safe Mode

Safe Mode with Network

►

Set the correct values for the attached monitor as described in the operating manual of the
monitor by selecting

Start - Settings - Control Panel - Display - Settings

Содержание SCENIC Edition X100


































































Результаты поиска

Содержание SCENIC Edition X100

Отзывы:

Похожие инструкции для SCENIC Edition X100

Бренды по названию

Популярные бренды

Fujitsu Siemens Computers SCENIC Edition X100, Руководство по эксплуатации

Результаты поиска

Содержание SCENIC Edition X100

Отзывы:

Похожие инструкции для SCENIC Edition X100

Бренды по названию

Популярные бренды