background image

Preparation: 

Alarm: 

 

Please don’t charging too long for the battery pack 

If the charging not finished in the stated time, please stop it, the 

battery pack may over heat and

 

smoking blast or build a fire. 

 

Please don’t put the battery pack into the microwave lamp or 

high voltage container 

The battery pack may over heat and smoking blast or build a fire. 

 

Please don’t close the broken battery pack to the fire 

If the battery pack broken and with the bad smell, please put them far 

from the flammable area. The electrolyte is easy to fire, may result in 

the battery pack smoking or fire. 

 

Please don’t use the exceptional battery pack 

If the battery pack smelled bad, different color, anamorphic or some 

other reason for the abnormity, please take off the battery pack from 

the charger or operation equipment and not to use. 

 

Please use the special charge 

The charge is special made for the 6200, it is scientific and more safe 

for charging to this model. This charge can identify the battery type 

for 6200 (Li-ion battery or Ni-H battery). 

 

 

Use the Li-ion battery pack 

 

Please charging before use it 

 

In order to reduce the discharge, please

 

take off the battery pack

 

and it on the shade and dryness place

 

 

When need long time to store the battery pack, please:

 

1.  Tack off the battery pack from the transceiver 

2. 

If possible, please discharge for the battery pack

 

3. 

Put the battery pack on the shade (

25

) and dryness place

 

 

The characteristic of the Li-ion battery 

 

The capacity reduce after charging again and again 

 

Even if not use the battery pack, it will also aging   

 

It is need more time in cool environment 

 

It may reduce the using life if charging in heat environment, the 

Содержание BF620001



















Отзывы: