background image

User’s manual · TSF 310 

 

         

- 6 -                 TSF  310                  version_en_1.1                FTE maximal 

 
- Modulation: Output modulation format: 4 (QPSK), 16 (16 QAM), 64 (64 QAM). 
- Advanced settings: 
 

- Mode: Selection of the modulation standard: DVB-T and DVB-H. 

 

Note: The output useful bits rate will depends on the following 
parameters: Bandwidth, guard interval, FEC codification and modulation. 
In the 

Attachment I 

you will find all the information related to the 

resulting useful bit rate in each configuration.  

 
 
 
5. Set Output channel  
In this option you can configure the different parameters of the cable signal.  
 
- Channel standard: It allows you to select the channelling of the cable signal 
standards. Options: BG, BG, PAL BG IT, 11, M NTSC, PAL M, PAL N, PAL DK , 
PAL I, BB_AU, DK PAL, L PAL.  
- Channel: Output channel of the cable modulation. When you select the output 
channel, the field “Frequency (MHz)” will be modified automatically, adapting itself 
to the selected channel. Options: C2-C69.  
- Frequency (MHz): Output frequency of cable modulation. When you modify this 
field, the field “Channel” will be also modified, indicating the channel equivalent to 
the selected frequency in the case that this frequency corresponds to the 
frequency of a channel. Options: 47-862 MHz.  
- Level: Regulation of the output level of the modulated signal. Options: 0-15dB.  
- Calibration: Allows the realization of two tests in order to verify the correct 
running of the device.  

- Deactivate output: It allows activating or deactivating the ouput of 
transmodulator.  

- Switch output to CW: It allows activating or deactivating the DVB-T / 
DVB-H modulation, allowing visualizing the carrier without modulation in 
the selected frequency. 

 

 
 
 

6. System 
This option provides information of the transmodulator.  
 
- System logfile: In this field are indicated the registered events in the module.  

- Read log: It allows reading the registered events in the module.  
- Clear log: It allows deleting all events stored until this moment.  
- Export log to USB:  It allows you to export all events registered to the 
connected USB device.  
- NM low Limit (dB): An event of error will be recorded when the value of 
Noise Margin is lower than the set value.  
- NM hight limit (dB): Once the event of error is recorded (Noise Margin 
< Limit Lower NM), this will be Noise Margin value that will have to be 
exceed so the module stops being in error. 
- Clear log all devices. It allows deleting the events report of all the 
interconnected modules. 

- Factory default: This option restores the values by default of the transmodulator.  
- System information: It allows you to visualize the basic information of the 
module: model, no of series, firmware version, etc. 
 
 
 
 
 
 
 
 
 

Содержание TSF 310





















Отзывы: