FTDI FT51A Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 171

FTDI FT51A Скачать руководство пользователя страница 28

Application Note

AN_289 FT51A Programming Guide

Version 1.0

Document Reference No.: FT_000962 Clearance No.: FTDI# 483

27

Document Feedback

Copyright © 2015 Future Technology Devices International Limited

transfer_size_done_int

interrupt in SPI_MASTER_INT. The

SPI_MASTER_DATA_DELAY

register must

be non-zero to use this method.

Data transfers can also be controlled by DMA: more details can be found in the DMA section of this
document.

2.3.1

SPI_MASTER_CONTROL

Bit

Position

Bit Field Name

Type

Reset

Description

7..2

Reserved

RFU

0

Reserved

1

spi_master_dev_en

R/W

0

Enable SPI Master

0

spi_master_soft_reset

R/W

0

Reset SPI Master

Table 2.23 SPI Master Control Register

The SPI Master Control register provides top-level enable and reset functions for the SPI Master
module.

The SPI Master module is enabled by setting the

spi_master_dev_en

bit to 1. Clearing this bit will

disable the module.

To reset the module, a 1 is written to the

spi_master_soft_reset

bit. This is cleared when the reset

is performed and will therefore always read as ‘0’.

2.3.2

SPI_MASTER_TX_DATA

Bit

Position

Bit Field Name

Type

Reset

Description

7..0

Data

R/W

0

Byte of data to clock out on SPI

Master bus.

Table 2.24 SPI Master Transmit Register

This register contains data to transmit from the Master to the Slave. Writing to this register will
start an SPI Master Write if a Slave Select (SS#) line is asserted.

2.3.3

SPI_MASTER_RX_DATA

Bit

Position

Bit Field Name

Type

Reset

Description

7..0

Data

R

0

Byte of data to clocked in on SPI

Master bus.

Table 2.25 SPI Master Receive Register

Data transmitted from the Slave to the Master is stored in this register. This will contain the data
clocked from the Slave during the previous Master Write.

«
...
26
27
28
29
30
...
»

Содержание FT51A












































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды