FSI DAT QE Series Скачать руководство пользователя

Страница: 6 / 27

PRINCIPLES OF OPERATION

FSI® Pneumatic showers/shelters are inflated via the use of a compressed air source/electric inflator/deflator

and inflation time is approximately 45 seconds to 5+ minutes (size of unit dependent).

Over

inflation of the structure is designed to be prevented via the inclusion of a pressure relief valve fitted to

the unit.

If using compressed air to inflate unit, an operator must stand by at all times and immediately

turn off compressed air source when the overpressure valve is activated as noted by the

“

hissing

”

sound of escaping air. At all times ensure the high pressure air fill hose is locked to the supplied O/D

ring on the air berm with the supplied locking wire.

The structure has reinforced air inflated berms and is usually fitted with two external zipped doors, the first is

the entrance door, and the second is the exit door at the other end as determined by on

scene coordinators.

To deflate the unit an inflation/deflation valve is so equipped to release the air in the structure via a quarter

turn

‘

push in

’

stem, allowing the FSI® shower/shelter to deflate. Use the supplied inflator/deflator to

’

suck

’

all

air out of the unit until flat to the naked eye. The unit can then be carefully folded, as it was received, and

packed into the carry sleeve/bag supplied for safe transportation and storage.

REMOVABLE

CANOPY

TIE DOWN ROPES AT

EACH CORNER TO

TIE FSI® SHELTER

OFF TO FIXED ITEMS

SUCH AS VEHICLES/

FENCES/POSTS/

POLES/OTHER IN

STRONG WINDS

DIRTY ENTRANCE DOOR

(CLEAN EXIT DOOR FROM

SHOWER AT OTHER END)

BUILT IN GROUNDSHEET

ATTACHED YET

REMOVABLE

FLOOR

INFLATABLE

STRUCTURE

FSI SHOWER/SHELTER DIAGRAMS

AIR BOTTLE INLET

ELECTRIC INFLATOR / DEFLATOR

INLET AND DUMP VALVE

INFLATION: Push in and quarter turn clockwise to lock

valve open. When unit fully inflated push in and quarter

turn counter clockwise to allow valve to pop up and

close. Your shower/shelter is now ready for use.

DEFLATION: To deflate, push in and quarter turn

clockwise to lock valve open. Air will rush out and unit

will begin to deflate. Ensure the tie down ropes are used

to assist the unit in returning to the ground by pulling

them toward each other allowing the unit to collapse into

its

’

own footprint. Use the deflation end of the electric

inflator/deflator to

‘

such

’

the remaining air out of the

unit until flat to the naked eye. Then push in and quarter

turn counter clockwise to allow valve to pop up and

close.

SAFETY OVER

PRESSURE VALVE

O/D RING

Содержание DAT QE Series




























Результаты поиска

Содержание DAT QE Series

Отзывы:

Похожие инструкции для DAT QE Series

Бренды по названию

Популярные бренды

FSI DAT QE Series, Инструкция по эксплуатации

Результаты поиска

Содержание DAT QE Series

Отзывы:

Похожие инструкции для DAT QE Series

Бренды по названию

Популярные бренды