Frymaster FPD65 Series Скачать руководство пользователя | Manualshive

Страница: 9 / 51

background image

FRYMASTER FPHD65 SERIES GAS FRYERS

CHAPTER 2: IMPORTANT INFORMATION

2-1

2.1 Receiving and Unpacking Equipment

A.

Check that the containers are upright. Use an outward prying motion -

no hammering

- to

remove the cartons. Unpack fryers carefully and remove all accessories from the carton
and/or frypots. Do not discard or misplace accessories, as they will be needed during final
assembly and fryer operation.

B.

After unpacking, immediately check the equipment for visible signs of shipping damage. If
damage has occurred, contact the carrier and file the appropriate freight claims. Do not
contact the factory. Shipping damage responsibility is between the carrier and the dealer.

If your equipment arrives damaged:

1.

File claim for damages immediately, regardless of extent of damage.

2.

Visible loss or damage: Be sure this is noted on the freight bill or express receipt and is
signed by the person making the delivery.

3.

Concealed loss or damage: If damage is unnoticed until equipment is unpacked, notify
freight company or carrier immediately, and file a concealed damage claim. This should
be done within 15 days of date of delivery. Be sure to retain container and all packing
materials for inspection.

NOTE:

Frymaster/Dean Does Not Assume Responsibility for Damage or Loss Incurred

in Transit.

C.

Built-in filtration cabinet:

Remove the filter pan from the cabinet before removing system

from pallet.

D.

Five- and Six-battery Frying Systems:

Units are shipped on two pallets. Casters are pre-

installed on the frying system and unloading ramps are furnished to facilitate removal of the
units off the pallets. Remove pallet supports from underneath fryer and carefully roll the unit
down the ramps from the front (cooking side).

See assembly instructions shipped with

unit for system assembly.

E.

Remove all plastic skin from sides, front, and doors of the fryers. Units are shipped with
plastic skin to protect the stainless components from surface damage during shipping.
Failure to remove the plastic prior to initial fryer operation will make it very difficult to
remove later.

«
...
7
8
9
10
11
...
»

Содержание FPD65 Series




















































Отзывы:

Нет отзывов

Похожие инструкции для FPD65 Series

CoolFry ADF-171N

Бренд: Aroma Страницы: 16

SilentDry MX00206

Бренд: MaxxDrySD Страницы: 4

Бренд: Gazi Страницы: 15

Бренд: Henny Penny Страницы: 69

Бренд: Oster Страницы: 20

Бренд: OldScool Страницы: 11

Бренд: Frigidaire Страницы: 2

Бренд: AUSPURE KITCHEN Страницы: 24

Бренд: SEVERIN Страницы: 172

Бренд: Siemens Страницы: 36

Бренд: Siemens Страницы: 48

Бренд: Yamato Страницы: 31

Бренд: Indesit Страницы: 12

Бренд: Whirlpool Страницы: 2

Бренд: Whirlpool Страницы: 28

Бренд: Whirlpool Страницы: 44

Бренд: Whirlpool Страницы: 44

Бренд: Whirlpool Страницы: 68

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды