Frymaster FPD65 Series Скачать руководство пользователя | Manualshive

Страница: 8 / 51

background image

FRYMASTER FPHD65 SERIES GAS FRYERS

CHAPTER 1: INTRODUCTION

1-3

1.6 Service Personnel

1.6.1 Definitions

A.

Qualified and/or Authorized Operating Personnel

1.

Qualified/authorized operating personnel are those who have carefully read the information
in this manual and have familiarized themselves with the equipment functions, or have had
previous experience with the operation of equipment covered in this manual.

B.

Qualified Installation Personnel

1.

Qualified installation personnel are individuals, or firms, corporations, or companies, which,
either in person or through a representative are engaged in and are responsible for the
installation of gas-fired appliances. Qualified personnel must be experienced in such work,
be familiar with all gas precautions involved, and have complied with all requirements of
applicable national and local codes.

C.

Qualified Service Personnel

1.

Qualified service personnel are those who are familiar with Frymaster/Dean equipment and
have been authorized by Frymaster/Dean to perform service on Frymaster/Dean equipment.
All authorized service personnel are required to be equipped with a complete set of service
parts manuals and stock a minimum amount of parts for Frymaster/Dean equipment. A list
of Frymaster

Factory Authorized Servicers (FAS’s) is located on the Frymaster website at

www.frymaster.com

.

Failure to use qualified service personnel will void the

Frymaster/Dean warranty on your equipment.

«
...
6
7
8
9
10
...
»

Содержание FPD65 Series




















































Отзывы:

Нет отзывов

Похожие инструкции для FPD65 Series

Бренд: T-Fal Страницы: 16

Бренд: COMAC Страницы: 2

Бренд: LOCO COOKERS Страницы: 18

Бренд: NEFF Страницы: 44

Бренд: Bosch Страницы: 28

Бренд: Bosch Страницы: 8

Бренд: Bosch Страницы: 8

Бренд: Bosch Страницы: 8

Бренд: Bosch Страницы: 32

Бренд: Bosch Страницы: 40

Бренд: Bosch Страницы: 40

Бренд: Bosch Страницы: 40

Бренд: Bosch Страницы: 56

Бренд: Bosch Страницы: 32

Бренд: Bosch Страницы: 36

Бренд: Bosch Страницы: 32

Бренд: Bosch Страницы: 44

Бренд: Bosch Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды