manualshive.com logo in svg

Frontier ST0522, Руководство оператора

Поделиться
Скачать
Frontier ST0522 Скачать руководство пользователя страница 16

WARNING: To connect a 120 volt power cord, always
connect the power cord first to the switch box located on

the engine and then plug the other end into a three-hole
grounded receptacle.

WARNING: To disconnect the power cord, always unplug
the end connected to the three-hole grounded receptacle

first.

How To Start A Cold Engine

1. Be sure auger drive and traction drive levers are in the disen-

gaged (

RELEASED

) position.

2. Rotate the 

choke knob

to the CHOKE position (see Figure 12).

3.

(Electric Start)

Plug the power cord into the 

starter motor

on

the engine. Plug the other end of power cord into a three-hole,
grounded 120 volt, AC receptacle.

4. Push the 

primer button

as specified below. Remove finger

from primer button between pushes (see Figure 13).

• Push two times if temperature is 15°F (-9°C) or higher.

• Push four times if temperature is below 15°F (-9°C).

5.

(Electric Start)

Connect the power cord to the engine and

depress the starter button (see Figure 14). To prolong the life
of the starter, do not crank for more than 5 seconds at a time.
Wait one minute between starts to allow the starter motor to
cool.

6.

(Recoil Start)

Slowly pull the 

recoil starter handle

until

resistance is felt and then pull rapidly to start the engine (see
Figure 15). Do not allow the 

recoil starter handle

to snap

back. Slowly return the 

recoil starter handle

.

7. If the engine does not start in 5 or 6 tries, See Difficult Starting

in the TROUBLE SHOOTING CHART.

8. Allow the engine to warm up for several minutes. As the

engine warms up, adjust the 

choke knob

toward the RUN

position. Wait until the engine runs smoothly before each
choke adjustment.

9.

(Electric Start)

First disconnect power cord from receptacle.

Then, disconnect the power cord from the 

switch box

.

If after following the preceding instructions, your engine fails to
start, have the engine checked by a John Deere/Frontier dealer. 

How To Start A Warm Engine

If restarting a warm engine after a short shutdown, leave the
choke lever in the off position and do not push the primer button.
If the engine fails to start, follow the Cold Start instructions.

Figure 15

Pull starter handle rapidly.

Figure 14

Starter Button

Key

Figure 13

Primer Button

Figure 12

Choke Control

OPERATION

16

Содержание ST0522

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды