Frontier LS2011, Руководство оператора

Страница: 21 / 68

5CS201115OM (rev 00 07/2020)
21
Speed in
MPH
Time (sec) required to travel a distance
of:
200 ft 300 ft
1.0 136 205
1.5 91 136
2.0 68 102
2.5 55 82
3.0 45 68
3.5 39 56
4.0 34 51
4.5 30 45
5.0 27 41
5.5 25 37
6.0 23 34
6.5 21 31
7.0 19 29
Determining Nozzle Size and Using
Calibration Chart
24 FT AND 30 FT BOOM CALIBRATION CHART
Tip Size PSI
GPM
one
nozzle
GPA (20” spacing)
4 MPH 5 MPH 6 MPH 8 MPH
AIC11004
30 0.35 26.0 21.0 17.3 13.0
40 0.40 30.0 24.0 19.8 14.9
50 0.45 33.0 27.0 22.0 16.7
60 0.49 36.0 29.0 24.0 18.2
18 FT BOOM CALIBRATION CHART
Tip Size PSI
GPM
one
nozzle
GPA (30” spacing)
4 MPH 5 MPH 6 MPH 8 MPH
AIC11004
30 0.35 17.3 14.0 11.5 8.7
40 0.40 20.0 16.0 13.2 9.9
50 0.45 22.0 18.0 14.7 11.1
60 0.49 24.0 19.3 16.0 12.1
The spray nozzles on your sprayer are
AIC11004, which match up with the calibration
chart. Refer to the calibration chart. Using
tractor speed, nozzle size, and desired gallons
per acre (GPA), calculate pressure (psi)
necessary
to achieve your GPA. It is important to note that
lower pressure settings will result in less spray
drift.
Example:
Assume tractor speed is determined to be 4
mph, nozzles are red (AIC11004) 30", and
desired GPA is 20 GPA. The calibration charts
shows that you should set sprayer’s
pressure at about 40 psi in order to apply 20
GPA.
Boomless Calibration
Right and Left Nozzles: 1/4XP20
Center Nozzle: 1/4TTJ08
BOOMLESS CALIBRATION CHART FOR 24”
HEIGHT
PSI
Cap. 3
Nozzle
GPM
Spray
Width
“ft”
GPA
4 MPH 6 MPH 8 MPH 10 MPH
30 4.2 26.3 19.7 13.1 9.9 7.9
40 4.8 30.3 19.6 13.1 9.8 7.8
50 5.4 32.3 21.0 13.8 10.3 8.3
60 6.0 33.3 22.0 14.8 11.1 8.9
BOOMLESS CALIBRATION CHART FOR 36”
HEIGHT
PSI
Cap. 3
Nozzle
GPM
Spray
Width
“ft”
GPA
4 MPH 6 MPH 8 MPH 10 MPH
30 4.2 27.3 19.0 12.7 9.5 7.6
40 4.8 31.3 19.0 12.7 9.5 7.6
50 5.4 33.3 20.0 13.4 10.0 8.0
60 6.0 35.3 21.0 14.0 10.5 8.4
Adjusting the Sprayer Pressure
NOTE: All calibration needs to be done with
clean water.
Once correct pressure setting has been
determined, the sprayer must be adjusted to
that pressure setting. Before adjusting sprayer’s
pressure, it is important to set tractor rpm at
rate that was used to determine tractor speed.
1. Loosen lock ring (A) and adjust knob (B) to
desired pressure. Pressure is displayed on
gauge (C).
2. Once desired pressure is achieved tighten
lock ring (A).
3. Sprayer is now calibrated.
Operation
A
C
B