Outdoor LP Gas Heater
Model No. GWU9850F / 35554 (A & B)
8
Operating Instructions
Checking for Leaks
W
WARNING: Before using this outdoor
fireplace, make sure you have read,
understand and are following all
information provided in the “Important
Safeguards” section. Failure to follow
those instructions can cause death,
serious injury or property damage.
Tank/Gas Line Connection
1 . Make 2-3 oz . of leak detection solution by mixing
one part liquid dishwashing soap with three parts
water .
2 . Make sure control knob is in the “ OFF” position
(Figure 3) .
3 . Connect LP gas tank per “Installing LP Gas Tank”
section .
4 . Turn LP gas tank valve to “OPEN .”
5 . Spoon several drops of solution, or use a squirt
bottle, at all “X” locations (Figures 1 and 2) .
a . If any bubbles appear, turn LP gas tank valve to
“CLOSED,” reconnect and re-test .
b . If you continue to see bubbles after several
attempts, turn LP gas tank valve to “CLOSED”
and disconnect LP gas tank, per “Disconnecting
LP Gas Tank” section . Contact 1 .800 .762 .1142
for assistance .
c . If no bubbles appear after one minute, turn
LP gas tank valve to “CLOSED,” wipe away
solution and proceed .
Lighting
W
WARNING: NEVER light the burner with
the cover on the heater.
W
CAUTION: Keep outdoor gas appliance
area clear and free from combustible
materials, gasoline and other
flammable vapors and liquids.
W
CAUTION: Do NOT obstruct the flow of
combustion and ventilation air.
W
CAUTION: Check and clean burner/
venturi tubes for insects and insect
nests. A clogged tube can lead to a
fire.
W
CAUTION: If relighting a hot heater,
always wait at least 5 minutes before
relighting.
Note: This heater is equipped with a pilot light that
allows for safer startups and shutdowns . Pilot must be
lit before main burner can be started .
Note: For your safety, the control knob cannot be
turned to the “ OFF” position without first depressing
control knob in (LOW/PILOT) position and then
rotating it to “ OFF .”
1 . Make sure all labels, packaging and protective
films have been removed from the patio heater .
2 . Check for obstructions of airflow to the burners .
Spiders, insects and webs can clog the burner/
venturi tube . A clogged burner tube can lead to
a fire .
3 . Control knob must be in the “ OFF” position
(Figure 3) .
4 . Connect LP gas tank per “Installing LP Gas Tank”
section .
5 . Perform leak check per “Checking for Leaks”
section .
6 . Turn LP gas tank valve to “OPEN .”
7 . Open viewing hole by sliding cover to either side
(Figure 6) .
8 . Push control knob in and rotate to (LOW/PILOT)
position (Figure 4) . For initial start or after any
tank change:
a . Hold control knob in for 2 minutes to purge
air from gas lines before proceeding
b . Then wait 5 minutes before lighting heater .
9 . Immediately push (igniter) button for five (5)
seconds . Pilot light flame will appear and be
visible through viewing hole (Figure 6) .
Figure 1
X
Figure 2
X
X
X
X
X
Figure 3
OFF /
ARRÊT
Figure 4
OFF /
ARRÊT
Figure 5
OFF /
ARRÊT
Figure 6
Viewing Hole
Figure 7
Burner
Flame
Slight
Yellow
Slight
Blue
Dark
Blue
Installing LP Gas Tank
To operate, you will need one precision-filled standard grill LP gas
tank with external valve threads .
W
CAUTION: LP gas tank must be properly
disconnected and removed prior to moving this
outdoor heater.
Insert LP Gas Tank
W
WARNING: Make sure LP gas tank valve is closed.
1 . Make sure control knob must be in the “ OFF” position (Figure 3) .
2 . Remove front shroud .
3 . Place precision-filled LP gas tank upright into the opening in the base so the tank valve is
facing the gas line connection .
Secure LP Gas Tank
1 . Secure tank in place by attaching loose end of tank retainer wire to hole in right leg .
2 . Replace front shroud .
Connecting LP Gas Tank
1 . Control knob must be in the “ OFF” position
(Figure 3) .
2 . Remove front shroud .
3 . Before connecting, be sure there is no debris
caught in the head of the LP gas tank, head of
the regulator valve or in the head of the burner or
burner ports .
4 . Connect regulator/hose assembly to tank by
turning knob clockwise until it stops .
5 . Perform leak check per “Checking for Leaks”
section .
6 . Replace front shroud .
Disconnecting LP Gas Tank
1 . Control knob must be in the “ OFF” position
(Figure 3) .
2 . Remove front shroud .
3 . Before disconnecting, make sure the LP gas tank
valve is “CLOSED .”
4 . Disconnect regulator/hose assembly from LP gas
tank by turning knob counterclockwise until it is
loose .
W
CAUTION: LP gas tank must be properly disconnected and removed
prior to moving this patio heater.
5 . Place the protective cap cover on the LP tank and store the tank outdoors in a well
ventilated area out of direct sunlight .
6 . Replace front shroud .
20 lb
9 Kg
17.9 in.
/ 45.5 cm
12.2 in. / 31 cm
