background image

7

 

 

C. To TILT your UMBRELLA: 

 

 

 
1. With the UMBRELLA FULLY OPEN, DEPRESS 
the BUTTON in the LIFT HANDLE.  See  
Diagram 16. 
 
2. While keeping the BUTTON in the LIFT HANDLE 
DEPRESSED, SLIDE the LIFT HANDLE DOWN the 
POLE until you reach your desired position.  There 
are several HOLES in the POLE (A) for you to lock 
the LIFT HANDLE into. You must line up the LIFT 
HANDLE with one of these holes or the LIFT 
HANDLE may drop down when you let go. See 
Diagram 16b. 
 

 

Diagram 16a                                                       Diagram 16b 

                 

 

 
3. Release the BUTTON in the LIFT HANDLE.  See 
Diagram 17.  It may be necessary to raise or lower 
the LIFT HANDLE slightly to get the pin to line up 
with the corresponding hole in the pole (A). 
 

Diagram 17 

 

 
D. To LOWER and CLOSE your UMBRELLA;

 

 
1. TURN the CRANK HANDLE (J) COUNTER 
CLOCKWISE until the UMBRELLA is FULLY 
CLOSED.  See Diagrams 18a and 18b. 

Diagram

 

18a

                                         

Diagram

 

18b

 

 

 
2. DEPRESS the TRIGGER in the LIFT HANDLE with 
your FINGERS. See close-up in Diagram 19a. 
 
3. While keeping the BUTTON in the LIFT HANDLE 
DEPRESSED, SLIDE the LIFT HANDLE DOWN as 
far as it will go.  The FABRIC part of the UMBRELLA 
should now be next to the POLE.  See Diagram 19b. 
 
4. RELEASE the BUTTON in the LIFT HANDLE. 

Diagram

 

19a

                                                

Diagram

 

19b

 

 

 

Содержание 140180B










Отзывы: