background image

6

 

 

II.

 

OPERATING

 

INSTRUCTIONS

 

A. To RAISE and OPEN your UMBRELLA;

 

 
1. GRASP the LIFT HANDLE firmly. 
 
2. DEPRESS the TRIGGER in the LIFT HANDLE with 
your FINGERS. See close-up in Diagram 12a. 
 
3. While keeping the BUTTON in the LIFT HANDLE 
DEPRESSED, SLIDE the LIFT HANDLE UP until it 
reaches the STOP.  See Diagram 12b. 
 
4.  RELEASE the BUTTON in the LIFT HANDLE. 

Diagram

 

12a

                                

Diagram

 

12b

 

 
5. TURN the CRANK HANDLE (J) CLOCKWISE until 
your UMBRELLA is fully OPEN.  See Diagram 13. 
 

Diagram

 

13

 

 

Your UMBRELLA can be ROTATED 360 degrees and TILTED to better protect you from the sun.   
B. To ROTATE your UMBRELLA; 
 
1. Lift up on the ROTATION HANDLE (G).  See 
Diagram 14a. 
 
2. While holding the ROTATION HANDLE (G) up,   
ROTATE the UMBRELLA by grasping the 
UMBRELLA (A) POLE firmly and turning it. See 
Diagram 14b. 

Diagram 14a                                           Diagram 14b 

 

 

 
3. When you reach the desired position, lower the 
ROTATION HANDLE (G) to lock the POLE (A) in 
place.  See Diagram 15a & b. 

Diagram 15a                                          Diagram 15b 

 

 

 

Содержание 140180B










Отзывы: