Fronius Virtual Welding Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 168

background image

12

Dangers from
mains current

An electric shock is potentially life threatening and can be fatal.

Do not touch live parts either inside or outside the device.

All cables and leads must be secured, undamaged, insulated and adequately
dimensioned. Loose connections, scorched, damaged or inadequately dimen-
sioned cables and leads must be repaired/replaced immediately.

Do not sling cables or leads around the body or parts of the body.

Arrange for the mains cable to be checked regularly by a qualified electrician
to ensure the ground conductor is functioning properly.

The device must only be operated on a mains supply with a ground conductor
and a socket with a ground conductor contact.

If the device is operated on a mains without a ground conductor and in a sock-
et without a ground conductor contact, this will be deemed gross negligence.
The manufacturer shall not be held liable for any damage arising from such
usage.
Switch off unused devices.

Wear a safety harness if working at height.

Before working on the device, switch it off and pull out the mains plug.

Attach a clearly legible and easy-to-understand warning sign to the device to
prevent anyone from plugging the mains plug back in and switching it on
again.

After opening the device:
-

discharge all live components

-

ensure that all components in the device are de-energised.

If work on live parts is required, appoint a second person to switch off the main
switch at the right moment.
Any repairs (e.g. opening of the terminal) must only be carried out by suitably
trained and qualified personnel. In the event of a fault, disconnect the mains
plug immediately and have repairs carried out by trained and qualified person-
nel.
-

The device must be disconnected from the power supply before carrying
out repairs.

-

Use only original spare parts

-

Switch off before removing the mains plug

«
...
10
11
12
13
14
...
»

Содержание Virtual Welding









































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Virtual Welding

MAGNUM ALERT-725

Бренд: NAPCO Страницы: 8

MAGNUM ALERT 854 SYSTEM

Бренд: NAPCO Страницы: 14

Бренд: NAPCO Страницы: 4

Бренд: NAPCO Страницы: 28

Бренд: NAPCO Страницы: 16

Бренд: Q Acoustics Страницы: 19

Бренд: Zeck Audio Страницы: 16

Бренд: Velleman Страницы: 3

Бренд: AmeriWater Страницы: 16

Бренд: Black Widow Security Страницы: 6

Бренд: R-Tech Страницы: 20

Oerlikon CITOCUT 25C

Бренд: Air Liquide Страницы: 68

Бренд: Daewoo Страницы: 21

ALSB106RD-Black180

Бренд: AmbiSonic Systems Страницы: 32

Бренд: Nxg Страницы: 2

SATURN 12 SYSTEM

Бренд: W Audio Страницы: 16

Бренд: Kühtreiber Страницы: 44

MegaWorks THX 6.1 650D

Бренд: Cambridge SoundWorks Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды