manualshive.com logo in svg

Fronius TransSteel 2200, Руководство по эксплуатации

Поделиться
Скачать
Fronius TransSteel 2200 Скачать руководство пользователя страница 132

Type of cooling

 

 

AF

Overvoltage category

 

 

III

Pollution degree according to IEC60664

 

3

EMC device class

 

A 

4)

Safety markings

 

S, CE, CSA

Dimensions l x w x h

 

560 x 215 x 370 mm

22.05 x 8.46 x 14.57 in.

Weight

 

 

15.2 kg

33.51 lb.

 

 

 

 

 

 

 

Max. shielding gas pressure

 

 

5 bar

72.52 psi

 

 

 

 

 

 

 

Wire speed

 

1.5 - 18 m/min

59.06 - 708.66 ipm

Wire drive

 

2-roller drive

Wire diameter

0.6 - 1.2 mm

0.025 - 0.047 in.

Wirespool diameter

 

max. 200 mm

max. 7.87 in.

Wirespool weight

 

max. 6.8 kg

max. 14.99 lb.

Max. noise emission (LWA)

 

65.5 dB

Idle state power consumption at
230 V

 

17.4 W

Power source efficiency at
210 A / 24.5 V

 

89 %

1)

Interface to a 230 V, 50 Hz public grid.

2)

Only applies to USA:
If an automatic circuit breaker is used instead of a fuse, the current/time charac-
teristic of the automatic circuit breaker must match that of the mains fuse spe-
cified above.
It is permitted for the tripping current of the automatic circuit breaker to be higher
than the tripping current of the mains fuse specified above.

3)

Only applies to USA:
Time-delay fuse conforming to UL Class RK5 (see UL 248).

4)

A device in emissions class A is not intended for use in residential areas in which
the electrical power is supplied via a public low-voltage grid.
The electromagnetic compatibility may be influenced by conducted or radiated
radio frequencies.

132

Содержание TransSteel 2200









































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды