manualshive.com logo in svg

Fronius TRANS STEEL 3500 C0MPACT, Инструкция по эксплуатации и список запасных частей

Поделиться
Скачать
Fronius TRANS STEEL 3500 C0MPACT Скачать руководство пользователя страница 99

97

g

tu2 | xxx

Remark: xxx stands for a temperature value

Cause:

Undertemperature in the power source secondary circuit

Remedy:

Place power source in a heated room and allow to warm up

tu3 | xxx

Remark: xxx stands for a temperature value

Cause:

Undertemperature in the wire-feed unit motor

Remedy:

Place wire-feed unit in a heated room and allow to warm up

tu4 | xxx

Remark: xxx stands for a temperature value

Cause:

Undertemperature in the welding torch

Remedy:

Place welding torch in a heated room and allow to warm up

tu5 | xxx

Remark: xxx stands for a temperature value

Cause:

Undertemperature in the cooling unit

Remedy:

Place cooling unit in a heated room and allow to warm up

tu6 | xxx

Note: xxx stands for a temperature value

Cause:

Undertemperature on the output choke of the power source

Remedy:

Place power source in a heated room and allow it to warm up

tu7 | xxx

Note: xxx stands for a temperature value

Cause:

Undertemperature in the power source

Remedy:

Place power source in a heated room and allow it to warm up

no | H2O

Cause: 

Coolant flow rate too low

Remedy:

Check coolant flow rate and cooling unit, including cooling circuit (for mini-
mum coolant flow, see "Technical Data" section in the device operating in-
structions)

hot | H2O

Cause: 

The coolant temperature is too high

Remedy:

Allow cooling unit and cooling circuit to cool down, until "hot | H2O" is no long-
er displayed. Open the cooling unit and clean the cooler, check fan is working 
properly. Robot interface or field bus coupler: before resuming welding, set 
the "Source error reset" signal.

no | Prg

Cause:

No preconfigured program has been selected

Remedy:

Select a configured program

Содержание TRANS STEEL 3500 C0MPACT

















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды