Fronius TPS/i Push Скачать руководство пользователя страница 45

Страница: 45 / 152

Control elements and mechanical components

Safety

WARNING!

Danger from incorrect operation.

This can result in severe personal injury and damage to property.

▶

All the functions described may only be used by trained and qualified personnel.

▶

Fully read and understand this document.

▶

Fully read and understand all the Operating Instructions for the system components,
especially the safety rules.

Control elements
and mechanical
components

(1)

(3)

(2)

(5)

(4)

No.

Function

(1)

Cover

(2)

Clamping lever

for setting the contact pressure of
the feed rollers

(3)

4-roller drive

(4)

Protective cover for the 4-roller
drive

(5)

Gas test / wire threading control
panel

Gas test/wire
threading control
panel (optional)

(1)

(2)

(3)

(4)

No.

Function

(1)

Operating status LED

Shows steady green when the
device is ready for use

No.

Function

(2)

Gas-test button

For setting the required gas flow rate on the pressure regulator
-

Gas will flow out for 30 seconds after the gas-test button is pressed. Press
the button again to stop the gas flow prematurely

(3)

Wire retract button

For retracting the wire electrode with no accompanying flow of gas or current
-

While the button is being pressed, the wirefeeder runs at the preset wire
retract speed

The wire electrode can be retracted using one of two methods:

Содержание TPS/i Push

























































































































































Результаты поиска

Содержание TPS/i Push

Отзывы:

Похожие инструкции для TPS/i Push

Бренды по названию

Популярные бренды

Fronius TPS/i Push, Руководство по эксплуатации

Результаты поиска

Содержание TPS/i Push

Отзывы:

Похожие инструкции для TPS/i Push

Бренды по названию

Популярные бренды