Fronius TPS/i Push Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 152

background image

The manufacturer accepts no liability for damage resulting from use of other system
components or a different coolant. In addition, all warranty claims will be forfeited.

Cooling Liquid FCL 10/20 does not ignite. The ethanol-based coolant can ignite under
certain conditions. Transport the coolant only in its original, sealed containers and keep
well away from any sources of ignition.

Used coolant must be disposed of properly in accordance with the relevant national and
international regulations. The coolant safety data sheet may be obtained from your ser-
vice centre or downloaded from the manufacturer's website.

Check the coolant level before starting to weld, while the system is still cool.

Commissioning,
maintenance and
repair

It is impossible to guarantee that bought-in parts are designed and manufactured to meet
the demands made of them, or that they satisfy safety requirements.
-

Use only original spare and wearing parts (also applies to standard parts).

-

Do not carry out any modifications, alterations, etc. to the device without the manu-
facturer's consent.

-

Components that are not in perfect condition must be replaced immediately.

-

When ordering, please give the exact designation and part number as shown in the
spare parts list, as well as the serial number of your device.

The housing screws provide the ground conductor connection for earthing the housing
parts.
Only use original housing screws in the correct number and tightened to the specified
torque.

Safety inspection

The manufacturer recommends that a safety inspection of the device is performed at
least once every 12 months.

The manufacturer recommends that the power source be calibrated during the same 12-
month period.

A safety inspection should be carried out by a qualified electrician
-

after any changes are made

-

after any additional parts are installed, or after any conversions

-

after repair, care and maintenance has been carried out

-

at least every twelve months.

For safety inspections, follow the appropriate national and international standards and
directives.

Further details on safety inspection and calibration can be obtained from your service
centre. They will provide you on request with any documents you may require.

Disposal

Do not dispose of this device with normal domestic waste! To comply with the European
Directive on Waste Electrical and Electronic Equipment and its implementation as
national law, electrical equipment that has reached the end of its life must be collected
separately and returned to an approved recycling facility. Any device that you no longer
require must either be returned to your dealer or given to one of the approved collection
and recycling facilities in your area. Ignoring this European Directive may have poten-
tially adverse affects on the environment and your health!

16

«
...
14
15
16
17
18
...
»

Содержание TPS/i Push

























































































































































Отзывы:

Нет отзывов

Похожие инструкции для TPS/i Push

Бренд: Bandit Страницы: 3

Бренд: BAMO IER Страницы: 40

Бренд: Walabot Страницы: 9

Бренд: i-onik Страницы: 59

Бренд: Jabra Страницы: 73

Бренд: TCL Страницы: 16

RAY-DANZ TS9030

Бренд: TCL Страницы: 32

Бренд: TCL Страницы: 19

Бренд: TCL Страницы: 16

Бренд: Wavetronix Страницы: 4

Бренд: X-10 Страницы: 32

Бренд: Watchguard Страницы: 8

Бренд: Jefferson Страницы: 24

Multi-room system

Бренд: Systemline Страницы: 22

Aqua-Pure 3MFF100

Бренд: 3M Страницы: 8

SITALI CXOM 180

Бренд: Olimpia splendid Страницы: 32

Бренд: LINNEPE Страницы: 7

Бренд: samet Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды