Fronius FRONIUS IS 15 Скачать руководство пользователя страница 41

Страница: 41 / 52

Error number 333

Over current

Cause:

Short circuit at AC output

Remedy:

Disconnect load, correct short circuit

Error number 334

Internal err

Cause:

Device error

Remedy:

Inform service

Error numbers 335 - 337

Internal err

Cause:

Device error

Remedy:

Inform service

Error number 391

Display lost

Cause:

Communication with display is not possible

Remedy:

Inform service

Error number 392

Display fault

Cause:

Display error

Remedy:

Turn device off/on

Error number 393

Old software

Cause:

AC processor software is incompatible with new firmware display
processor

Remedy:

Update software (service)

Error number 401

Slave fault

Cause:

The master device has detected an error in a slave device in multi-
phase operation

Remedy:

Correct error at slave device

Error number 402

Sync lost

Cause:

Synchronization signal from master device has not been received
multiple times

Remedy:

Check communication connection

Error number 403

Sync lost

Cause:

A reset was triggered at the parallel bus

Remedy:

Device will correct error automatically

Error number 404

No slave

Cause:

Error in communication setup in multi-device operation

Remedy:

Check setup settings and communication connections and correct if

necessary

Error number 405

Old firmware

Cause:

Configuration error after service

Remedy:

Carry out firmware update

Error number 406

Ph cfg err

Cause:

Incorrect phase system setting

Remedy:

Check device settings and communication connections

Displayed Ser-
vice Codes

(continued)

Содержание FRONIUS IS 15





















































Результаты поиска

Содержание FRONIUS IS 15

Отзывы:

Бренды по названию

Популярные бренды

Fronius FRONIUS IS 15, Руководство по эксплуатации

Результаты поиска

Содержание FRONIUS IS 15

Отзывы:

Бренды по названию

Популярные бренды