manualshive.com logo in svg

Fronius FlexTrack 45, Инструкция по эксплуатации/Перечень запасных частей, Страница: 28 / 90

Поделиться
Скачать
Fronius FlexTrack 45 Скачать руководство пользователя страница 28

28

Remote control 

elements

(continued)

(6) Traversing direction

Selects the traversing direction.

(7) Travel speed

Regulates the travel speed of the welding carriage.

(8) Welding mode

3 welding modes can be selected: 

 - Test 

 - Without arc (O) 

 - With arc (I)

(9) White symbols: Weaving mode

Four weaving modes can be selected: 

 - No weaving

 - Trapezoidal weaving

 - Box weaving

 - Triangular weaving

Green marking: Preset path measurement

Preset to select the additional path measurement function (green symbol) on the 

weaving path button (10).

Yellow marking: Preset segment welding

Preset to select the additional segment welding function (orange symbols).

IMPORTANT!

 The welding process cannot start until the weaving mode adjusting 

knob (9) is set to one of the white function parameters.

(10) White symbol: Weaving path

Regulates the weaving path.

Green symbol: Total welding path

Total welding path in [cm].

(11)

White symbol: End-crater filling time

Enables the weld seam to be finished smoothly. 

IMPORTANT:

 Parameters must be entered via the power source and must be 

either equal to or greater than the power source value.

Yellow symbol: Start-up delay / Flying-start

If value is positive – start-up delay [s]: Start welding -> Dwell time elapses -> 

Carriage starts to move.

If value is negative – flying-start [s]: Carriage starts to move. The arc does not 

ignite until the “flying start” time has expired.

Содержание FlexTrack 45



























































































Отзывы:

Нет отзывов