Fronius FK 6000 Скачать руководство пользователя

Страница: 32 / 40

Troubleshooting

Safety

Troubleshooting

Not enough coolant circulation, or none at all

Cause:

Coolant level is too low

Remedy:

Top up the reservoir with coolant

Cause:

Constriction or foreign body in the cooling circuit

Remedy:

Eliminate the constriction or foreign body

Cause:

Fuse for coolant pump is faulty

Remedy:

Replace the coolant pump fuse, as described in the section headed “Fuse
protection of the cooling-unit”

Cause:

Coolant pump is faulty

Remedy:

Replace the coolant pump

Cause:

The coolant filter in the plug-type connector for coolant return-flow is blocked

Remedy:

Clean the coolant filter with clean tap water or replace the filter-insert

Cause:

Permissible duty cycle exceeded

Remedy:

Await cooling-down phase of the coolant pump

Cooling capacity too low

Cause:

Fan defective

Remedy:

Replace fan

Cause:

Cooling pump defective

Remedy:

Replace coolant pump

Cause:

Cooler contaminated

Remedy:

Clean cooler with dry compressed air

Cause:

Cooling capacity of cooling unit too low

Remedy:

Use cooling unit with higher cooling capacity

WARNING!

An electric shock can be fatal. Before opening up the unit:

Shift the mains switch into the “O” position

Unplug the unit from the mains

Put up an easy-to-understand warning sign to stop anybody inadvertently
switching it back on again

Using a suitable measuring instrument, check to make sure that electrically
charged components (e.g. capacitors) have been discharged

CAUTION!

Inadequate PE conductor connections can cause serious injury and

damage. The housing screws provide a suitable PE conductor connection for
earthing (grounding) the housing and must NOT be replaced by any other screws
which do not provide a reliable PE conductor connection.

Содержание FK 6000









































Результаты поиска

Содержание FK 6000

Отзывы:

Похожие инструкции для FK 6000

Бренды по названию

Популярные бренды

Fronius FK 6000, Инструкция по эксплуатации и список запасных частей

Результаты поиска

Содержание FK 6000

Отзывы:

Похожие инструкции для FK 6000

Бренды по названию

Популярные бренды