manualshive.com logo in svg

Fronius Acerios, Руководство по эксплуатации

Поделиться
Скачать
Fronius Acerios Скачать руководство пользователя страница 35

Installation

Safety

WARNING!

Danger from electrical current.

This can result in serious personal injury and damage to property.

▶

Before starting work, switch off all devices and components involved, and
disconnect them from the grid.

▶

Secure all devices and components involved so they cannot be switched back
on.

▶

After opening the device, use a suitable measuring instrument to check that
electrically charged components (such as capacitors) have been discharged.

WARNING!

Danger of electrical current due to electrically conductive dust in the device.

This can result in severe personal injury and damage to property.

▶

Only operate the device if an air filter is fitted. The air filter is a very import-
ant safety device for achieving IP 23 protection.

General

A standard configuration is used to describe the installation and start-up of the
plasma system.

The standard configuration consists of the following system components:

-

Acerios plasma power source (including robot interface)

-

FK 9000 R cooling unit

-

PCT 2000 plasma torch

-

Gas pressure regulator

-

Gas cylinder with process gas

-

Upright console

-

Gas control 5 - 30 l

The following steps should provide an overview of plasma system installation and
start-up.
For detailed information about the individual steps, please refer to the corres-
ponding Operating Instructions for the system components.

Installation

WARNING!

Danger due to incorrect operation.

Serious personal injury and damage to property may result.

▶

All the functions described may only be used by trained specialist personnel.

▶

Read and understand this document in full.

▶

Read and understand all the Operating Instructions for the system compon-
ents, especially the safety rules, in full.

Requirement:

-

The components for an automated application (e.g. robot, robot control sys-
tem, longitudinal chassis, rotary tables, etc.) must be present and ready for
use.

35

EN-US

Содержание Acerios





















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды