Fromm FS1 2109 V01 Series Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 49

background image

FS1.2109-Manual 32.42XX.XXX.V01-V02-V03-EN08_R2.doc

FROMM

it is forbidden to duplicate this manual or parts of it in any way or any form without written permission of the author © 2017

website: www.fromm-stretch.com

11

WARNINGS



The mean weighed noise level of the machine is less than 80 dBa. It is possible that, depending on

the applied film, during wrapping of the pallets / products incidentally a noise level with a maximum
of 80 dBa will be measured. Carrying of noise protecting devices is advised.



One has to reckon with the possibility that the film (roll) contains an electrostatic charge.



Utmost caution has to be taken with respect to the complete electrical installation. ONLY trained

persons may carry out activities to it, after having taken the required safety measures as mentioned
in the chapter

SAFETY INSTRUCTIONS

.



One has to reckon with the European safety requirements and standards if the machine has to be

adapted and thus safety measures or protection covers also have to be adapted.



Touching the electrical equipment will hazard your personal safety.



Persons who carry out changes in or adaptations (function, operation or principles) to the machine

are fully responsible for those changes and/or adaptations.



All relevant safety measures should be taken when carrying out any activity on the machine,

especially during maintenance activities and solving failures.

Take care that the main switch is switched off (position "0") and locked (If possible), or that the power
cable is disconnected in order to prevent other persons in putting in action the machine during your
activities.

All the normally valid safety measures or customs with respect to safety should also be taken during
those activities.



Playing with or around the machine may cause dangerous situations with a machine in operation.

This playing is never allowed!



All other prescriptions and laws with respect to working conditions and safety on the working spot

should be observed with this machine.



An acoustic signal device has been installed in the control cabinet, which will be activated first during

a short period, as a warning every time before the machine is starting.

«
...
9
10
11
12
13
...
»

Содержание FS1 2109 V01 Series


















































Отзывы:

Нет отзывов

Похожие инструкции для FS1 2109 V01 Series

Бренд: ABB Страницы: 36

Бренд: ABB Страницы: 40

Бренд: GALLERY Страницы: 18

Бренд: B&K Страницы: 12

Бренд: KaVo Страницы: 49

Бренд: Easson Страницы: 33

Бренд: Garmin Страницы: 10

Бренд: Naviom Страницы: 31

Бренд: K-LASER Страницы: 70

Бренд: K-LASER Страницы: 72

Бренд: KaVo Страницы: 4

ORTHOPANTOMOGRAPH OP 3D

Бренд: KaVo Страницы: 40

KEY Laser III 1243

Бренд: KaVo Страницы: 103

EXTRAmatic 9040

Бренд: KaVo Страницы: 56

ESTETICA E70 Vision

Бренд: KaVo Страницы: 48

Бренд: Kaya Safety Страницы: 5

Бренд: XTA Страницы: 20

Бренд: Kawai Страницы: 166

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды