Fritsch PULVERISETTE 1 classic line Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 56

Fritsch PULVERISETTE 1 classic line Скачать руководство пользователя страница 18

CAUTION!
The weight of the jaw crusher is
Model I: 177 kg
Model II: 205 kg

NOTICE!
The Laboratory - jaw crusher must be placed on a flat,

stable surface. It can be screwed onto it or a base plate.

1.

The jaw crusher is screwed to the pallet from below using 4

screws. Unscrew the screws with a 17 mm spanner.

2.

Lash the harnesses to a crane or another hoist.

3.

Next, lash the harness to the two eyelets provided for this purpose

on the front and back of the device.

4.

Lift the device off the transport pallet.

5.

To avoid movements of the machine during the grinding process,

mount the included feet with the corresponding rubber pads on

the 4 corners of the machine that were previously attached to the

transport pallet.

6.

Screw the 4 feet into the correct threads from below and lock

them from the top using the included lock nuts.

7.

Using a crane, bring the jaw crusher to the desired position and

place the anti‐slip mats below the 4 feet. When positioning the

device, make sure it does not swing when it is suspended from the

crane.

8.

Remove the harnesses.

Installation

- 18 -

«
...
16
17
18
19
20
...
»

Содержание PULVERISETTE 1 classic line

























































Отзывы:

Нет отзывов