manualshive.com logo in svg

Fristam Pumps FKL-150, Инструкция по эксплуатации и техническому обслуживанию, Страница: 4 / 50

Поделиться
Скачать
Fristam Pumps FKL-150 Скачать руководство пользователя страница 4

Fristam Pumps
4

R

EFERENCE

 M

ATERIAL

 

T

EChNICAL

 I

NFORMATION

S

PECIFICATIONS

Normal Differential Pressure Range ......................................................................... 0 to 300 PSI
Normal Speed Range ............................................................................................... 0 to 600 RPM
Normal Temperature Differential (Standard Rotors) ........................................................

∆

140°F

Normal Temperature Differential (High Temperature Rotors) ........................................

∆

10°F

M

ATERIALS

 

OF

 C

ONSTRUCTION

Major Product Contact Components ...............................................................AISI 316L (CF3M)
Rotors ................................................................................................. Non-galling Stainless Steel
Cover Gasket .......................................................................................................BUNA (standard)
 

Also available in ...................................Viton, EPDM and other options available

Surface Finish for Product Contact Surfaces .................................................... 3 Ra (standard)
 

Also available in ........................................................................... 5 Ra and 0 Ra 

Cover Gasket and Other O-rings on Aseptic ....................................................................... EPDM

S

hAFT

 S

EALS

 & O-

RINgS

Mechanical Seal Type ............................................................................................. Single/Double
Stationary Seal Ring Material ..........................................................................Carbon (standard)
 

Also available in ...........................................Silicon Carbide & Chrome oxide/SS

Rotating Seal Ring Material ............................................................................. Chrome Oxide/SS
 

Also available in ............................................................................ Silicon Carbide

Other O-rings (mechanical seals) .......................................................................Viton (standard)
 

Also available in ..............................................EPDM and other options available

O-ring Seal Type ..................................................................................................... Single/Double
O-ring Seal Material ............................................................................................Viton (standard)
 

Also available in ..................................... EPDM and other availableupon request

Note: o-ring seal not available on the FKL 400 

L

UbRICATION

Oil Grade ..................................................................................................................... SAE 15W40
Oil Capacity - Horizontal
     FKL 5 .......................................................................................... 1.66 liters (1.75 US quarts) 
     FKL 50 .............................................................................................. 1.4 liters (1.5 US quarts)
     FKL 75 .............................................................................................. 4. liters (4.5 US quarts)     
     FKL 150 ............................................................................................ 7.1 liters (7.5 US quarts)
     FKL 50 ........................................................................................... 10.4 liters (11 US quarts)
     FKL 400 ........................................................................................ 17.5 liters (18.5 US quarts)
Oil Capacity - Vertical
     FKL 5 .......................................................................................... 0.65 liters (0.75 US quarts) 
     FKL 50 .............................................................................................. 1.4 liters (1.5 US quarts)
     FKL 75 ........................................................................................... .6  liters (.75 US quarts)
     FKL 150 .......................................................................................... 3.9 liters (4.5 US quarts)
     FKL 50 ............................................................................................ 4. liters (4.5 US quarts)
     FKL 400 ............................................................................................ 8.0 liters (8.5 US quarts)

Содержание FKL-150



















































Отзывы:

Нет отзывов