Frigidaire GRFC2353AD страница 17 Скачать руководство пользователя

Страница: 17 / 52

WARNING

To avoid electric shock, which can

cause death or severe personal injury,

disconnect the refrigerator from

electrical power before connecting a

water supply line to the refrigerator.



NOTE

Check with your local building au-

thority for recommendations on water

lines and associated materials prior

to installing your new refrigerator.

Depending on your local/state build-

ing codes, Frigidaire recommends for

homes with existing valves its

Smart

Choice

water line kit 5305513409 with

a 6 ft. (1.8 meters) Stainless Steel Water

Line, and for homes without an existing

valve Frigidaire recommends its

Smart

Choice

water line kit 5305510264 with

a 20 ft. (6 meters) Copper Water Line

with self-tapping saddle valve. Please

refer to www.frigidaire.com/store for

more information.

CAUTION

To Avoid Property Damage:
• Copper or Stainless Steel braided

tubing is recommended for the

water supply line. Water supply

tubing made of

inch plastic is

not

recommended

to be used. Plastic

tubing greatly increases the potential

for water leaks, and the manufacturer

will not be responsible for any

damage if plastic tubing is used for

the supply line.

• DO NOT install water supply tubing

in areas where temperatures fall

below freezing.

• Chemicals from a malfunctioning

water softener can damage the ice

maker. If your home has a water

softening system, ensure the softener

is maintained and working properly.

IMPORTANT

Ensure that your water supply line con-

nections comply with all local plumbing

codes.

Before Installing The Water

Supply Line, You Will Need:

• Basic Tools: adjustable wrench,

flat-blade screwdriver, and Phillips

screwdriver

• Access to a household cold water

line with water pressure between 30

and 100 psi.

• A water supply line made of

inch

(6.4 mm) OD, copper or stainless

steel tubing. To determine the

length of tubing needed, measure

the distance from the water inlet

valve at the back of the refrigerator

to your cold water pipe. Then add

approximately 6 ft. (1.8 meters), so

the refrigerator can be moved out

for cleaning (as shown).

• A shutoff valve to connect the water

supply line to your household water

system. DO NOT use a self-piercing

type shutoff valve.

• Do not re-use compression fittings

or use thread seal tape.

• A compression nut and ferrule

(sleeve) for connecting a copper

water supply line to the ice maker

inlet valve.

To Connect Water Supply Line

To Main Water Inlet Valve

1. Disconnect refrigerator from electric

power source.

2. Place end of water supply line

into sink or bucket. Turn ON water

supply and flush supply line until

water is clear. Turn OFF water

supply at shutoff valve.

3. Remove plastic cap from water valve

inlet and discard cap.

WATER SUPPLY CONNECTION

Содержание GRFC2353AD





















































Результаты поиска

Содержание GRFC2353AD

Отзывы:

Похожие инструкции для GRFC2353AD

Бренды по названию

Популярные бренды

Frigidaire GRFC2353AD, Инструкция по использованию и уходу

Результаты поиска

Содержание GRFC2353AD

Отзывы:

Похожие инструкции для GRFC2353AD

Бренды по названию

Популярные бренды