background image

GAS WALL OVEN INSTALLATION INSTRUCTIONS

4

5. Cabinet Installation

A.  Model With 1½ Oven Cavity

Insert appliance into cutout.  Use the 4 mounting screws
provided to fasten the front frame of the appliance to
the cabinet (steps 1 below). Keep the 2 decorative
screws to fix the decorative trim to the cabinet (step 2
below). The mounting holes in the front frame of
appliance may be used as a template to locate the
appliance mounting screw holes on the cabinet.

To fasten the appliance to the cabinet (figure 6):

1. Use 4 mounting screws supplied to secure the

appliance to the cabinetry. 2 holes are located under
the center vent trim on each side, the 2 other holes
are visible when the drawer is opened.

2.

Optional:

 Install the decorative trim under the

appliance (as shown on figure 6) using the 2
decorative screws supplied with the appliance.

4. Adjusting Oven Height

(Model with 1 ½ oven cavity only)

Remove and lay aside the lower vent decorative trim
that is taped to the side or to the top of the oven.  The
decorative trim will be fastened to the lower front of the
oven after it has been installed in the cabinet.

There is a 1 ½" height adjustment on models with
extension panel (see figure 4).  With this adjustment and
a ½" trim overhang, a unit can be installed in existing
openings 37 ½" to 39" high.

Figure 4

Oven Door

Oven Bottom

Extension Panel

Figure 5

To adjust oven height:

1. Lay oven on its back. (see figure 5).
2. Remove the 6 screws that fasten the side extension

panel to the bottom sides of the oven.

3. Move each panel down to the position that increases

the oven height to fit your opening. Each position
changes oven height approximately ½".

4. Line up the appropriate holes in the side extension

panels and sides of the oven. Put the 6 screws back.

5. Proceed with oven installation. Return to upright

position.

Figure 6

Adjustment

Holes

Extension Panel

Mounting Screws

Center Vent Trim

Decorative Trim

Mounting Screws

Mounting

Screws

Decorative Screws

Содержание FGB24T3ESC





















Отзывы: