Friendly Robotics RL550 Скачать руководство пользователя страница 50

Страница: 50 / 54

Whenever replacing the blades, it is recommended to restart the counter of the blades replacement
reminder by choosing the

‘Blades replaced’

option under the ‘

User Preferences’

menu and press the GO

button again to clear the reminder.

Figure 8.1

Squeeze tabs & pull

To remove blades, squeeze locking tabs on each side of blade retainer,

then pull blade assembly off, away from mower. When reinstalling the

blade, line up the mating splines and push until a firm click is heard,

indicating a proper seating of the blade onto the shaft

Squeeze here

Locking tabs

Mating spline

Figure 8.2

Using a wooden stick or similar object, clean accumulated grass from these
areas of the mowing deck. Remove blades if necessary for better access.

CAUTION! ALWAYS REMOVE

POWER PACK BEFORE

SERVICING BLADES!

Содержание RL550























































Результаты поиска

Содержание RL550

Отзывы:

Бренды по названию

Популярные бренды

Friendly Robotics RL550, Инструкция по эксплуатации и безопасности

Результаты поиска

Содержание RL550

Отзывы:

Бренды по названию

Популярные бренды