Friendly Robotics RL550 Скачать руководство пользователя страница 45 | Manualshive

Страница: 45 / 54

background image

45

Problem Encountered

Probable Cause/Event

Corrective/User Action

-

Weak batteries

-

Install fresh alkaline C-cell batteries

-

Poor wire splicing (confirm that

when the Perimeter Switch is turned
on, first the ‘Cut wire’ indicator is
flashing once).

-

Twisted cables, or a screw terminal,

insulated with insulation tape is not
a satisfactory splice. Soil moisture
causes the conductors to oxidize
and after a while result in broken
circuit.

-

Use the connectors supplied in the box. It is
waterproof and gives a reliable electrical
connection.

‘Replace Battery’

indicator

flashing on Perimeter Switch

-

Perimeter wire too long for one

zone

-

A maximum perimeter wire length of 1000 feet
(300 m) is recommended. Areas requiring
longer lengths should be broken into separate
zones. If the ‘Cut Wire’ indicator flashes once
when the Perimeter Switch is activated, this
confirms a length too long for a single
perimeter zone.

-

Mower is in deep sleep.

-

If not connected to the charger at all times
when not in use, the Robomow will conserve
power by entering into a deep sleep mode. Lift
Power Pack from mower and re-insert it after
10 seconds.

Robomow will not operate and

nothing will display on the

LCD screen.

-

Power Pack has been discharged

from lack of charge maintenance.

-

It is required for the charger to remain
connected to the Robomow when not in use.
Failure to do so can cause permanent Power
Pack damage. Contact your service provider.

Robomow drives but blades

will not mow.

-

‘Mowing ‘has been turned to off.

-

Change back on under ‘User Preferences’

-

Power Pack is not fully charged

-

Connect the charger to the mower and keep it
connected until the ‘Ready – Keep Charging’
message displays in the LCD screen.

-

‘Work Time ‘ for that zone is set to

stop at a pre-determined duration.

-

Work time can be changed under ‘User
Preferences’

-

Grass is extremely over grown or

very wet.

-

Raise cutting height. Always mow the grass
frequently enough to prevent over growth.
Refrain from cutting wet grass.

-

Power Pack is reaching a normal

end of life state.

-

Replace Power Pack. Properly maintain Power
Pack per instructions.

Short run time, operates less

time than normal.

-

Manual Controller is not firmly

pivoted down flush in holder,
allowing it to bounce up and stop the
mower.

-

Confirm the coiled cord is fully placed into the
holder below the Manual Controller and the
Manual Controller closes flush with the top of
the mower.

Robomow operating lamp
flashes once when Power

Pack is inserted, but no

display is seen in the LCD

display.

-

Power Pack fuse has not been
installed.

-

Install Power Pack fuse.

«
...
43
44
45
46
47
...
»

Содержание RL550























































Отзывы:

Нет отзывов

Похожие инструкции для RL550

Бренд: Yard-Man Страницы: 16

Бренд: Cadet Страницы: 44

Бренд: Yard Machines Страницы: 44

Бренд: Yardworks Страницы: 21

Бренд: Gardena Страницы: 9

Wheel Horse 265-6

Бренд: Toro Страницы: 44

Бренд: Greencut Страницы: 68

Бренд: Gardeline Страницы: 19

GrandStand 74574

Бренд: Toro Страницы: 68

Бренд: Bolens Страницы: 32

Бренд: Yard Machines Страницы: 16

ZERO TURN MOWERS

Бренд: Bush Hog Страницы: 30

Бренд: Yard-Man Страницы: 28

Time Saver i1042

Бренд: Cub Cadet Страницы: 112

Бренд: Kubota Страницы: 132

Бренд: Jonsered Страницы: 47

Бренд: Cub Cadet Страницы: 40

sunjoe 24V-CRLM15

Бренд: SNOWJOE Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды