manualshive.com logo in svg

Friendly Robotics RL550, Инструкция по эксплуатации и безопасности

Поделиться
Скачать
Friendly Robotics RL550 Скачать руководство пользователя страница 34

 

34 

 Chapter 4 

Charging 

 

4.1   Charging 
 

Of all the areas regarding the Robomow, proper charging of the Power Pack is second only to safety in 
importance.  Failure to follow the charging guidelines will result in poor performance and a short Power 
Pack life.  After the completion of any daily cutting session it is very important to bring the Robomow to its 
storage area and plug it into the charger as soon as possible, preferably within 6 hours from the time it 
stopped.  

 

The standard charger, Figure 4.1 is actually a power supply, where the voltage output is DC and the 
current flowing to the Power Pack for re-charging is regulated inside the mower. The charging system and 
Power Pack are designed such that they can remain plugged in at all times of non-use without concern to 
over charging, over heating or damaging the Power Pack.  In fact, it is the preferred way to maintain your 
Power Pack, always keep it plugged into the charger when not being used. The standard charger (power 
supply) will re-charge the Power Pack from the 

‘Recharge Battery’

 level in approximately 20 hours, 

depending on conditions.  There is a fast charger available as an accessory.  See the accessories 
available for your Robomow in Chapter 10. 

 

 

4.2   Charging Using the Standard Charger Connected to the Charging Socket 

 

 
Connect the charger to a regular household receptacle, 120 Volts AC 

(models outside the US utilize 230 

volts mains power)

 and the output lead of the charger, Figure 4.2, into the charging socket, located under 

the Manual Controller holder, Figure 4.3, and the charging process will begin. Lightly pivot the Manual 
Controller down, allowing it to rest gently on the charging cord.  DO NOT attempt to force the Manual 
Controller all the way to the flush position. The Robomow charger is designed for indoor dry use only.  Do 
not charge the Robomow where wet contact is likely.   

 
 
 
 
 
 
 
 

 

 
 
 
 
 
 
 
 
 
 
 
 
 

Standard charger (power 

supply) 120 volt shown

 

Figure 4.1 

Charger output lead

Figure 4.2 

Standard charger 

connector socket

Figure 4.3 

!

Shock hazard.  Injury or electrocution can occur. The Robomow 

standard charger is designed for indoor use in dry locations only.  

Never use the charger or charge the Robomow in areas where 

extreme dampness or wet contact is likely.  Never use a charger 

when the leads are damaged.  Use only the recommended charger 

with your Robomow. 

WARNING!

 

Содержание RL550























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды